10-11-2010
copy the configuration to another:
- interface (e1000g2/3 and maybe 0 because this interface is working)
- switchport
if the config works on another port, the port e1000g1 might be faulty. if it won't work, your config might be bad.
to investigate further, please post the files:
/etc/hostname.*
/etc/hosts
/etc/netmasks
10 More Discussions You Might Find Interesting
1. IP Networking
I am trying to network two solaris workstations(ultra sparc 5) at home. what shoud I use to build the one of workstations as a http and ftp server and to network with the other workstation?
(please explain to me in detail.. what kind of software or equipment do I need..)
Thanks
John (1 Reply)
Discussion started by: jung1975
1 Replies
2. IP Networking
Hi,
How to check whether a port is working properly or not ?
I am getting a Error message Could not open connection to the host, on port 23: Connect failed.
Thanks !! (1 Reply)
Discussion started by: dreams5617
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies
4. Solaris
may i know what is the command for configure
new ip, subnet mask and gateway ??
thanks .. (3 Replies)
Discussion started by: Farbegas
3 Replies
5. IP Networking
hi all,
how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface... (1 Reply)
Discussion started by: itik
1 Replies
6. Solaris
I have just installed Solaris 10 for x86. The install seemed to have worked fine, and I have configured my hostname and am able to login and do whatever. However, networking does not seem to have been installed. I have a router which assigns ip address via DHCP. I would have thought Solaris would... (5 Replies)
Discussion started by: Phobos
5 Replies
7. UNIX for Advanced & Expert Users
Hi all,
When I tried to restart the networking daemon, it stated this error:
MyServer:/etc/init.d# ./networking restart
Reconfiguring network interfaces...RTNETLINK answers: Network is unreachable
run-parts: /etc/network/if-up.d/route exited with return code 2
done.
Please note that I... (2 Replies)
Discussion started by: mjdousti
2 Replies
8. IP Networking
Hi all
Right, i need to admit Im c4p on networking. I hate it, always have, always will. Here's my problem
Ive got 3 hosts. A B and C. I need to directly contact host C from host A, but at the moment I have to ssh on to B, to then ssh on to C.
so, I need to set up host b, to forward... (3 Replies)
Discussion started by: sbk1972
3 Replies
9. Solaris
Hi,
I have installed two solaris boxes in an VM.
First box is 10-1
Has two interfaces and in connected briged to the lan an d connected internal to an virtual lan.
Second box is 10-2
Has one interface.
Now what I wanted to do is a setup so that 10-2 connects through 10-1 to the lan.... (3 Replies)
Discussion started by: jld
3 Replies
10. UNIX for Dummies Questions & Answers
Hello,
I am using dual boot of linux, one is ubuntu and the other is one is centos.
I have three NIC's and only one of them connected with cable.
The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet.
When I boot from the centos I am not... (6 Replies)
Discussion started by: programAngel
6 Replies
LEARN ABOUT OSF1
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)