Sponsored Content
Operating Systems Solaris Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)? Post 302460667 by ctafret on Thursday 7th of October 2010 09:22:28 AM
Old 10-07-2010
Question Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"

Details --

According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:
lrwxrwxrwx 1 root root 110 Oct 6 08:22 c9t6d0s6 -> ../../devices/iscsi/disk@0000iqn.1986-03.com.sun%3A02%3A7baf5e59-8829-44bf-d575
-e8931cf3bb16.watch0001,0:g,raw


When I tried fdisk, on slice 2 or 6 I get:
# fdisk /dev/rdsk/c9t6d0s6
Error in ioctl DKIOCGMBOOT: Invalid argument
No fdisk table exists. The default partition for the disk is:

a 100% "SOLARIS System" partition

Type "y" to accept the default partition, otherwise type "n" to edit the
partition table.

(going through the motions of this ends in the error again when you exit)

When I try any other slice or
c9t6d0s2:c
I get:
fdisk: Cannot open device /dev/rdsk/c9t6d0s2:c

Is it possible to mount any kind of pcfs iSCSI target on a Solaris (sparc) initiator?
 

9 More Discussions You Might Find Interesting

1. BSD

Mount Fat32,ext3

Hello All, How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies

2. Solaris

How can I mount a ufs filesystem on a solaris 10 sparc onto a Linux server

Hi there, I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server. *I have re-compiled the linux kernel t support ufs fstype with ro mount support. filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies

3. Solaris

Solaris 10 10/08 sparc + iSCSI

hi, I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work. Thanks, Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies

4. Solaris

Iscsi - target + initiator on the same host.

Hi all iscsiadm / iscsitadm. Ive created two devices on a host. # iscsitadm list target Target: 1-disk0 iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0 Connections: 1 Target: 1-disk1 iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies

5. UNIX for Advanced & Expert Users

LTO2 tape drive as iSCSI target

I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies

6. UNIX for Advanced & Expert Users

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies

7. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

8. HP-UX

Unable to delete iscsi target

Hi Please can someone give me a hint on this, when I list the targets, I see two o them: #iscsiutil -p Operational Target Information ------------------------------ Target # 1 ----------- Target Name : iqn.1992-08.com.netapp:sn.142241859 Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies

9. Linux

How to boot iSCSI target from console linux?

I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
cmdk(7D)							      Devices								  cmdk(7D)

NAME
cmdk - common disk driver SYNOPSIS
cmdk@target, lun : [ partition | slice ] DESCRIPTION
The cmdk device driver is a common interface to various disk devices. The driver supports magnetic fixed disks and magnetic removable disks. The block-files access the disk using the system's normal buffering mechanism and are read and written without regard to physical disk records. There is also a "raw" interface that provides for direct transmission between the disk and the user's read or write buffer. A sin- gle read or write call usually results in one I/O operation; raw I/O is therefore considerably more efficient when many bytes are transmit- ted. The names of the block files are found in /dev/dsk; the names of the raw files are found in /dev/rdsk. I/O requests to the magnetic disk must have an offset and transfer length that is a multiple of 512 bytes or the driver returns an EINVAL error. Slice 0 is normally used for the root file system on a disk, slice 1 as a paging area (for example, swap), and slice 2 for backing up the entire fdisk partition for Solaris software. Other slices may be used for usr file systems or system reserved area. Fdisk partition 0 is to access the entire disk and is generally used by the fdisk(1M) program. FILES
/dev/dsk/cndn[s|p]n block device (IDE) /dev/rdsk/cndn[s|p]n raw device (IDE) where: cn controller n dn lun n (0-7) sn UNIX system slice n (0-15) pn fdisk partition(0) /kernel/drv/cmdk 32-bit kernel module. /kernel/drv/amd64/cmdk 64-bit kernel module. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |x86 | +-----------------------------+-----------------------------+ SEE ALSO
fdisk(1M), mount(1M), lseek(2), read(2), write(2), readdir(3C), scsi(4), vfstab(4), attributes(5), dkio(7I) SunOS 5.10 9 Oct 2004 cmdk(7D)
All times are GMT -4. The time now is 11:01 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy