10-06-2010
Wireless configuration on My linux
Hello All
Please can some one help me to use my USB wireless card D-Link on my laptop
i want to configure it, I am using madriva 2010 my system Acer Aspire 4315
i want to know how to configure it and where to get special driver to download the driver
Please
10 More Discussions You Might Find Interesting
1. IP Networking
Can I set up Linux on a Mobo with WiFi to serve as a Server and Wireless Router for my home? (3 Replies)
Discussion started by: andou
3 Replies
2. Linux
hi all,
:)
Please let mew know some useful link that has some information about wireless set-up and configuration for Linux FC-8 on laptop.
-regards
Ashvin (2 Replies)
Discussion started by: Ashvin Gaur
2 Replies
3. SuSE
Hi
I've done some google searching but haven't really found anything that seems to be what I need. First I should add it's been awhile since I have run Linux but that's changing :)
What I'm after doing is setting up a Linux box as a wireless router. I will be running the Suse distro if I... (2 Replies)
Discussion started by: woofie
2 Replies
4. UNIX for Dummies Questions & Answers
so i downloaded a linux today,
but i ahve the problem that i cant connect to the internett becouse i need drivers.
annyone know where i can get the drivers? (4 Replies)
Discussion started by: Morton
4 Replies
5. Red Hat
Hello,
I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies
6. UNIX for Advanced & Expert Users
Hi,
Could some please help me in configuring wireles internet on redhat linux installed on my laptop.
When I booted using windows, I saw the following, which I think is the name of my laptop's wireless card:
Intel(R) PRO/Wireless 3945ABG Network Connection
I have run the following steps... (1 Reply)
Discussion started by: girish1428
1 Replies
7. Red Hat
Hi,
Could some please help me in configuring wireles internet on redhat linux installed on my laptop.
When I booted using windows, I saw the following, which I think is the name of my laptop's wireless card:
Intel(R) PRO/Wireless 3945ABG Network Connection
I have run the following steps... (9 Replies)
Discussion started by: girish1428
9 Replies
8. Linux
I am running Linux Mint Gloria on my PC. I have ADSL broadband connection which require login and pswd connection to connect. I have SmartAX MT841 modem which has wireless card free with it. I also have recently purchased DELL inspiron 1545 machine which have Vista preinstalled in it. Now I want to... (0 Replies)
Discussion started by: budtuxy
0 Replies
9. Linux
I just installed linux mint 11 yesterday. I cannot get the wireless to register, it says that firmware is missing but I can not figure out how to make it work. I am still a newbie and would appreciate any help possible. Thank you. (7 Replies)
Discussion started by: breebutner
7 Replies
10. IP Networking
hi all:
I want to find a wireless test tool for linux , just linke netstumbler on windows . i find the tool for long time , but i cann't find one. does somebody give a advice. thanks!!! (0 Replies)
Discussion started by: arnold.king
0 Replies
DAIC(4) BSD Kernel Interfaces Manual DAIC(4)
NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards
SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10
DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO.
For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd
system, which can be listed using the daicctl utility.
The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should
allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto-
col and some parts of the cards interface are ISDN protocol dependent.
The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992.
MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd.
Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l
to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu-
mentation for details.
The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called
download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under
dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile
will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte-
grated. But if you own a card, you do have the file (or can get it from the Diehl web server).
SEE ALSO
daicctl(1)
BUGS
The driver is not yet finished.
BSD
January 30, 1998 BSD