i have a file which contains text as shown below....
aaa|bbb|ccc|ddd|
cccc|ddddd|eeeee|ffffff
want to convert pipe symbol to tab like
aaaa bbbb cccc ddddd
ccccc ddddd eeeee ffffffffff
i tried with sed
sed 's/|/\t/g' file_name ...but i could not... (1 Reply)
I have various column names within double quotes, separated by commas.
Example:
"column one", "column number two", "this is column number three", anothercolumn, yetanothercolumn
I need to eliminate the double quotes and replace the blanks within the double quotes by underscores, giving:
... (5 Replies)
Hi All Gurus,
I need to replace a pipe <|> with a comma <,> in a few columns with pipe delimited file. The column name are fixed for the replacement of comma <,>.
For below example, Col3, Col6 and Col8 are columns need to replace with comma <,> if any pipe encountered.
example:... (14 Replies)
I want to replace the whitespace with Pipe symbol to do a multiple pattern matching for the whole text "mysqld failed start" and same as for other text messages Below are the messages stored in a file seperate by whitespace
mysqld failed start
nfsd mount failed
rpcbind failed to start
for... (6 Replies)
Well as the title describes, its a pretty straight forward problem. I have a series of psql tables where there are lots of blanks. However there is at least one column, called name, that will never be blank. I want to write a select statement to get all of the contents of the table and then turn... (3 Replies)
I have file like below
abc 12 34 45 code
abcdef 451 1 4 code
ghtyggg 4 56 3 code
I need to change this to
abc|12|34|45|code|
abcdef|451|1|4|code|
ghtyggg|4|56|3|code|
I tried replace space with | in sed ... but in the middle some row has... (7 Replies)
Hi All,
I am trying to replace the values inside <password> tag in an xml file but it doesn't replace certain passwords:
For eg:
Server/home/sperinc>cat TextXML.txt
<appIds>
<entry name="AccountXref">
<type id="ldap">
<realm>nam</realm>
... (7 Replies)
Hi Folks!
Need a solution for the following :-
Source data
-------------
123|123|<CRLF><CRLF><CRLF>|321<CRLF>
Required output
------------------
123|123|<LF><LF><LF>|321<CRLF>
<CRLF> represents carriage return
<LF> represents line feed
Being hunting high and low for a... (10 Replies)
with in my files i have the data like this, starting with a pipe and ending the line with a pipe.
all i want is to replace the first and last pipe , remove those
trying to use following sed command, but it is only showing on the screen the entire data of the file as if it removed, but when i... (4 Replies)
Discussion started by: cplusplus1
4 Replies
LEARN ABOUT DEBIAN
dh-exec
DH-EXEC(1) dh-exec DH-EXEC(1)NAME
dh-exec - Debhelper executable file helpers
SYNOPSIS
#! /usr/bin/dh-exec
src/libfoo-*.so.* debian/foo-plugins/usr/lib/foo/${DEB_HOST_MULTIARCH}/
etc/example.conf => debian/foo/etc/foo/foo.conf
DESCRIPTION
dh-exec is a simple program, meant to be used as the interpreter for executable debhelper config files.
It is a wrapper around the various other sub-commands (see below), and will pipe the input file through all of them in turn, using an
ordering that makes most sense in the vast majority of cases.
The order as of now is dh-exec-subst gets run first, followed by dh-exec-install, so that variable expansion happens before files need to
be copied.
ARCHITECTURE
dh-exec is built up from three layers: there is the dh-exec utility, its single entry point, the only thing one will need to call.
Below that, there are the various sub-commands, such as dh-exec-subst, dh-exec-installs and dh-exec-illiterate, which are thin wrappers
around the various dh-exec scripts, that make sure they only run those that need to be run.
And the lowest layer are the various scripts that do the actual work.
One can control which sub-commands to run, or if even more granularity is desired, one can limit which scripts shall be run, too. See below
for the options!
OPTIONS
--with=command[,command ...]
Replace the list of sub-commands to run the input through with a custom list (where entries are separated by whitespace or commas).
This option will always replace the existing list with whatever is specified.
This can be used to explicitly set which sub-commands to use.
The list must not include the dh-exec- prefix.
Defaults to subst,install.
--without=command[,command ...]
Inversely to the option above, this lists all the sub-commands which should not be used.
The list must not include the dh-exec- prefix.
--with-scripts=script[,script ...]
Replace the list of scripts to run the input through with a custom list (where entries are separated by whitespace or commas). This
option will always replace the existing list with whatever is specified.
This can be used to explicitly specify which scripts to use, limiting even beyond what the --with option is capable of.
The list must not include the dh-exec- prefix.
By default it is empty, meaning there is no filtering done, and whatever scripts the sub-commands find, will be run.
--no-act
Do not really do anything, but print the pipeline that would have been run instead.
--list
List the available sub-commands and scripts, grouped by sub-command.
--help, --version
Display a short help or the package version, respectively.
SUB-COMMANDS
dh-exec-subst
Substitutes various variables (either from the environment, or from dpkg-architecture(1)).
dh-exec-install
An extension to dh_install(1), that supports renaming files during the copy process, using a special syntax.
ENVIRONMENT
DH_EXEC_LIBDIR
The directory in which the wrapped sub-commands reside. Defaults to /usr/lib/dh-exec/.
DH_EXEC_SCRIPTDIR
The directory in which the scripts that do the heavy work live. Defaults to /usr/share/dh-exec/.
FILES
$DH_EXEC_LIBDIR/dh-exec-*
The various sub-commands.
$DH_EXEC_SCRIPTDIR/dh-exec-*
The various scripts ran by the sub-commands.
SEE ALSO debhelper(1), dh-exec-subst(1), dh-exec-install(1)AUTHOR
dh-exec is copyright (C) 2011-2012 by Gergely Nagy <algernon@madhouse-project.org>.
2012-05-03 DH-EXEC(1)