tar: Memory allocation failed for extended data while reading : Not enough space
what can be done for the above problem?
top utility reports memory usage as follows:
Memory: Real: 2688M/15G act/tot Virtual: 1492M/42915M use/tot Free: 11G
this cannot be a disk space problem as we have... (1 Reply)
I am trying to compile the pro*C file but gives errors. It says it encountered "std" while it was expecting ; , = ( $ $ORACLE_HOME/bin/proc tradewind/dataaccess/Blob.pcc
Pro*C/C++: Release 10.2.0.3.0 - Production on Fri May 9 11:10:54 2008
Copyright (c) 1982, 2005, Oracle. All rights... (0 Replies)
In our directory there are too many files, & if I try to execute mv *.gz or rm *.l command it fails, providing error string as - 'arg list too long'. This doesnt happen always, is there any way we know, limit on the rm & mv command so we can take care of this failure in future executions ? (9 Replies)
Hi All,
I have a process running on my AIX 5.3 server box. The process runs fine for 5-6days but then crashes. The log file shows malloc failure and the svmon (Virtual memory size), ps -lef (SZ value) are also gradually increasing. But unfortunately MALLOCDEBUG and any other memory debugging... (3 Replies)
Hi,
My program was running for a whole night. after 12 hours i got an error message "Cannot allocate memory" during the shmat commmand. So can you please let me know what could be the reason? is there any solution?
thanks in advance.
Regards,
Mano (5 Replies)
Hi,
In my proj, one process was running for 2 days. after 2 days its throwing an error message "shmget failed cannot allocate memory". the same problem happened every time.i.e. i can reproduce the same issue if my process is running for every 2 days for a same operation.Within this 2 days there... (1 Reply)
Hi,
In my proj, one process was running for 2 days. after 2 days its throwing an error message "shmget failed cannot allocate memory". the same problem happened every time.i.e. i can reproduce the same issue if my process is running for every 2 days for a same operation.Within this 2 days there... (1 Reply)
Hi,
In my proj, one process was running for 2 days. after 2 days its throwing an error message "shmget failed cannot allocate memory". the same problem happened every time.i.e. i can reproduce the same issue if my process is running for every 2 days for a same operation.Within this 2 days there... (1 Reply)
Hi ,
Our one of VMguest all lvm got unmounted once the machine is rebooted
when in repair state dmesg its showing an error out of memory killed process 22289 (lvm)
please refer screen shots attached
when i look the lvscan its showing all lvm are inactive
i checked throuh top there... (0 Replies)
Discussion started by: venikathir
0 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)