IBM support provided a efc_power program to measure the transmit (TX) and RX (receive) strength. They stated it works with most Emulex fiber cards. If a server reports the TX less than -10, then the card is probably bad. If the RX is less than -10, then cabling or the SAN port is probably bad.
Hello,
I create a file touch 1201093003 fichcomp
and inside a repertory (which hava a lot of files) I want to list all files created before this file :
find *.* \! -maxdepth 1 - newer fichcomp but this command returned bash: /usr/bin/find: Argument list too long
but i make a filter all... (1 Reply)
I'm not sure if this is the right forum for this or not but we use a program called "Password Safe" to store the many root passwords we have for our Unix system.
Now we are being called out by our security team to prove that this is a safe program to use. So far I have been able to determine... (1 Reply)
I need to periodically run a check on the passwords of the users (Redhat 5.0) to verify that all passwords meet minimal standards. I remember seeing a script years ago that grabbed the encrypted passwords from the file and checked if they matched any of the encrypted strings in another file, plus... (1 Reply)
For moderator: I made a new thread in a proper part of the forum now https://www.unix.com/homework-coursework-questions/137119-user-processes.html
But now i wan't to make something which isn't related to a homework, so i hope
you won't close this one. Thanks to those two answers, you helped me!... (9 Replies)
I have read the forums for strengthing the openssl ciphers on a server and the following command I can run:
openssl ciphers -v 'TLSv1+HIGH:!SSLv2:RC4!MEDIUM:!aNULL:!eNULL:!3DES:!EXPORT:@STRENGTH'
I have some services that cannot be set to higher levels like you can set in an httpd.conf file.... (1 Reply)
I need assistance with following requirement, I am new to Unix.
I want to do the following task but stuck with file creation date(sysdate)
Following is the requirement
I need to create a script that will read the abc/xyz/klm folder and look for *.err files for that day’s date and then send an... (4 Replies)
Discussion started by: PreetArul
4 Replies
LEARN ABOUT FREEBSD
mfi
MFI(4) BSD Kernel Interfaces Manual MFI(4)NAME
mfi -- LSI MegaRAID SAS driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device mfi
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mfi_load="YES"
DESCRIPTION
This driver is for LSI's next generation PCI Express SAS RAID controllers. Access to RAID arrays (logical disks) from this driver is pro-
vided via /dev/mfid? device nodes. A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.
The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
thus requires a new driver. Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.
Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume. By default the driver will
disallow any requests to remove a mounted volume. If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
mounted volumes to be removed.
A tunable is provided to adjust the mfi driver's behaviour when attaching to a card. By default the driver will attach to all known cards
with high probe priority. If the tunable hw.mfi.mrsas_enable is set to 1, then the driver will reduce its probe priority to allow mrsas to
attach to the card instead of mfi.
HARDWARE
The mfi driver supports the following hardware:
o LSI MegaRAID SAS 1078
o LSI MegaRAID SAS 8408E
o LSI MegaRAID SAS 8480E
o LSI MegaRAID SAS 9240
o LSI MegaRAID SAS 9260
o Dell PERC5
o Dell PERC6
o IBM ServeRAID M1015 SAS/SATA
o IBM ServeRAID M1115 SAS/SATA
o IBM ServeRAID M5015 SAS/SATA
o IBM ServeRAID M5110 SAS/SATA
o IBM ServeRAID-MR10i
o Intel RAID Controller SRCSAS18E
o Intel RAID Controller SROMBSAS18E
FILES
/dev/mfid? array/logical disk interface
/dev/mfi? management interface
DIAGNOSTICS
mfid%d: Unable to delete busy device An attempt was made to remove a mounted volume.
SEE ALSO amr(4), pci(4), mfiutil(8)HISTORY
The mfi driver first appeared in FreeBSD 6.1.
AUTHORS
The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.
BUGS
The driver does not support big-endian architectures at this time.
BSD July 15, 2013 BSD