hi all
when i trying to give auto-boot value as false as following
#eeprom auto-boot?=false
it is showing as
zsh: no matches found: auto-boot?=false
so felt this is because of error in hard ware so i tried this
can any one please help me
what is the problem and what should i do
Last edited by DukeNuke2; 09-28-2010 at 05:26 AM..
After upgrading to solaris 10 (from sol 8) on a SUN Blade 1500, it seems that the dvd/cd-rom does not accept dvds nor cds in the dvd drive.
After I insert a dvd/cd in the drive, the disk is simply ejected (!)
Is it possible that the upgrade made the system not being able to recognize these... (2 Replies)
Hi everyone,
I am having a problem when running devfsadm. We have many T2000, but on one of them, that is connected to our SAN, devfsadm reports no new disks. If a reconfiguration reboot is done, the system reports the new disk. But only with a reboot. We have Solaris10 installed and Veritas... (13 Replies)
Hi,
I have a netra t2000 running solaris 10. It is fully patched with the latest patch cluster and also patch 118833-36 and 126897-02. The SC sys_event level is set to 3.
I am running a test to show hardware log status, e.g simulating a power supply failure.Hence I unplug one of te... (3 Replies)
Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch.
After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Friends ,
I want to install package using yum from DVD in RHEL 5 . Hence I just follow the below rules :
1)
# mount /dev/hdc /cdrom/
mount: block device /dev/hdc is write-protected, mounting read-only
2)
Edit the yum rhel-debuginfo.repo file like following way :
# pwd... (3 Replies)
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Hi all,
First post so be gentile :)
It's my first time installing Solaris on T2000 server.
I have 2 72GB HD's on it.
After configuring HW raid and running raidctl command I get this output:
bash-3.00# raidctl -l c0t0d0
Volume Size Stripe Status Cache RAID
... (2 Replies)
Hi,
I have a problem controlling devices on my iMac.
The internal DVD is no longer working. Therefore I have bought a new external DVD, but some programs use the internal by default.
Since iMac, runs UNIX beneath the Mac OS X, I hope to do some magic, by unmounting the internal DVD and put... (0 Replies)
Discussion started by: ASL123
0 Replies
LEARN ABOUT CENTOS
systemd-efi-boot-generator
SYSTEMD-EFI-BOOT-GENERATOR(8) systemd-efi-boot-generator SYSTEMD-EFI-BOOT-GENERATOR(8)NAME
systemd-efi-boot-generator - Generator for automatically mounting the EFI System Partition used by the current boot to /boot
SYNOPSIS
/usr/lib/systemd/system-generators/systemd-efi-boot-generator
DESCRIPTION
systemd-efi-boot-generator is a generator that automatically creates mount and automount units for the EFI System Partition (ESP), mounting
it to /boot. Note that this generator will execute no operation on non-EFI systems, on systems where the boot loader does not communicate
the used ESP to the OS, on systems where /boot is an explicitly configured mount (for example, listed in fstab(5)) or where the /boot mount
point is non-empty. Since this generator creates an automount unit, the mount will only be activated on-demand, when accessed.
systemd-efi-boot-generator implements the generator specification[1].
SEE ALSO systemd(1), systemd.mount(5), systemd.automount(5), systemd-gpt-auto-generator(8), gummiboot(8), fstab(5)NOTES
1. generator specification
http://www.freedesktop.org/wiki/Software/systemd/Generators
systemd 208SYSTEMD-EFI-BOOT-GENERATOR(8)