Have you checked to see if your NIC actually supports turning off auto-negotiation? What happens when you execute the following fro the command line:
Also, is this NIC bonded or a slave?
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5.
#ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Hello,
here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data... (3 Replies)
Discussion started by: demerzel3
3 Replies
LEARN ABOUT OPENSOLARIS
ral
ral(7D) Devices ral(7D)NAME
ral - Ralink RT2500 802.11b/g Wireless driver
DESCRIPTION
The ral 802.11b/g wireless NIC driver is a multi-threaded, loadable, clonable, GLDv3-based STREAMS driver supporting Ralink RT2500
chipset-based NIC's.
CONFIGURATION
The ral driver performs auto-negotiation to determine the data rate and mode. Supported 802.11b data rates are 1, 2, 5.5 and 11 Mbits/sec.
Supported 802.11g data rates are 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbits/sec. The ral driver supports only BSS networks (also
known as "ap" or "infrastructure" networks) and "open"(or "open-system") or "shared system" authentication.
FILES
/dev/ral*
Special character device.
/kernel/drv/ral
32-bit ELF kernel module (x86).
/kernel/drv/amd64/ral
64-bit ELF kernel module (x86).
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWralink |
+-----------------------------+-----------------------------+
|Interface stability |Committed |
+-----------------------------+-----------------------------+
SEE ALSO dladm(1M), wificonfig(1M), attributes(5), gld(7D), dlpi(7P)
802.11 - Wireless LAN Media Access Control and Physical Layer Specification -- IEEE, 2001
SunOS 5.11 25 Jun 2007 ral(7D)