|
|
Sponsored Content
Operating Systems
Solaris
M5000 boot net- install failed
Post 302456038 by DukeNuke2 on Thursday 23rd of September 2010 04:53:29 AM
09-23-2010
|
|
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do you install linux over the net? (1 Reply)
Discussion started by: macdonto
1 Replies
2. Solaris
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
Hi my friends
when I want to make boot net for my server I have receive:
Time out ARP/RARP
note: I have use
Ok boot net (this is my Syntax)
so what is the problem? (2 Replies)
Discussion started by: bintaleb
2 Replies
4. Solaris
I have a blade 6000 chassis with a T6340 blade. The blade took a dump and I am trying to rebuild it with a Flash Archive. I am using net boot from an E2900 and the flash is located on a an array that is attached to my v245 management server. I can net boot and I can select flash install. When I put... (1 Reply)
Discussion started by: ryan_ford
1 Replies
5. AIX
dears
i am trying to upgrade the TL from TL7 to TL8 and i facing this issue AIX6.1
<< End of Success Section >>
+-----------------------------------------------------------------------------+
BUILDDATE Verification ...... (2 Replies)
Discussion started by: thecobra151
2 Replies
6. Solaris
Dear all,
I have a solaris 10 in my environment (VMware virtual machine). recently I increased the harddisk size from the VMware and reboot my server. after reboot the os is unable to boot and gives the below error message.
exec(/sbin/init) file not found
press any key to restart
... (3 Replies)
Discussion started by: krishna001
3 Replies
7. Solaris
I have M10-1. Installation OS 10 from cdrom external.
Here message from OK Prompt
{0} ok probe-scsi-all
/pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1
Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00
But..
{0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
8. Solaris
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
Discussion started by: goya
3 Replies
LEARN ABOUT SUNOS
check-hostname
check-hostname(1M) System Administration Commands check-hostname(1M) NAME
check-hostname - check if sendmail can determine the system's fully-qualified host name SYNOPSIS
/usr/sbin/check-hostname DESCRIPTION
The check-hostname script is a migration aid for sendmail(1M). This script tries to determine the local host's fully-qualified host name (FQHN) in a manner similar to sendmail(1M). If check-hostname is able to determine the FQHN of the local host, it reports success. Other- wise, check-hostname reports how to reconfigure the system so that the FQHN can be properly determined. FILES
/etc/hosts Host name database /etc/nsswitch.conf Name service switch configuration file /etc/resolv.conf Configuration file for name server routines ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWsndmu | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
sendmail(1M), hosts(4), attributes(5) SunOS 5.10 10 Nov 2003 check-hostname(1M)