09-22-2010
M5000 boot net- install failed
Good evening all,I'm new to your site, so please bear any infringements or transgressions on my part.I'm new to the whole Solaris boot install over the net scenario, but here's where I'm stuck:I have an M5000 with 2 domains (running unimode). Domain 0 is configured and running Solaris 10. Domain 1 has no OS. There is only one DVD on the system and is accessible from one domain at a time (and requires system board swapping). It can be maide accessible to the other domain but that requires the running side to be shutdown (which I cannot do).So I've created a jumpstart server and it "looks" like it's working. (I get rpcinfo replies from it)It is said that to boot the domain over the net simply type:boot net - installfrom the o prompt. This done from XSCF, I get the dreaded "Can't locate boot device"immediately on pressing return. Makes me think that it's not even trying to look on the network for the Jumpstart server...All suggestions welcome and thanks in advanceRS
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do you install linux over the net? (1 Reply)
Discussion started by: macdonto
1 Replies
2. Solaris
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
Hi my friends
when I want to make boot net for my server I have receive:
Time out ARP/RARP
note: I have use
Ok boot net (this is my Syntax)
so what is the problem? (2 Replies)
Discussion started by: bintaleb
2 Replies
4. Solaris
I have a blade 6000 chassis with a T6340 blade. The blade took a dump and I am trying to rebuild it with a Flash Archive. I am using net boot from an E2900 and the flash is located on a an array that is attached to my v245 management server. I can net boot and I can select flash install. When I put... (1 Reply)
Discussion started by: ryan_ford
1 Replies
5. AIX
dears
i am trying to upgrade the TL from TL7 to TL8 and i facing this issue AIX6.1
<< End of Success Section >>
+-----------------------------------------------------------------------------+
BUILDDATE Verification ...... (2 Replies)
Discussion started by: thecobra151
2 Replies
6. Solaris
Dear all,
I have a solaris 10 in my environment (VMware virtual machine). recently I increased the harddisk size from the VMware and reboot my server. after reboot the os is unable to boot and gives the below error message.
exec(/sbin/init) file not found
press any key to restart
... (3 Replies)
Discussion started by: krishna001
3 Replies
7. Solaris
I have M10-1. Installation OS 10 from cdrom external.
Here message from OK Prompt
{0} ok probe-scsi-all
/pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1
Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00
But..
{0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
8. Solaris
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
Discussion started by: goya
3 Replies
LEARN ABOUT PHP
asadmin-stop-domain
asadmin-stop-domain(1AS) User Commands asadmin-stop-domain(1AS)
NAME
asadmin-stop-domain, stop-domain - stops the given domain
SYNOPSIS
stop-domain [--domaindir install_dir/domains][--terse=false] [--echo=false] [domain_name]
stop-domain stops the specified domain. If there is only one domain in the default domain directory (install_dir/domains), then no operand
is required to stop the domain. However, if there is more than one domain, the domain operand must be specified. This command is supported
in local mode only.
OPTIONS
--domaindir directory where the domain is to be stopped. If specified, path must be accessible in the filesystem. If not speci-
fied, the domainis stopped in the default install_dir/domains directory.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
OPERANDS
domain_name name of the domain. Must be a unique name.
Example 1: Using stop-domain
asadmin> stop-domain sampleDomain
Stoping Domain sampleDomain, please wait
Domain sampleDomain stopped
Command stop-domain executed successfully
Where: the sampleDomain domain in the default domains directory is stopped.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-delete-domain(1AS), asadmin-start-domain(1AS), asadmin-list-domains(1AS)
J2EE 1.4 SDK March 2004 asadmin-stop-domain(1AS)