09-21-2010
..great..
..but finaly i solved the problem unplugging the netmgt interface.
Probably something was going bad with that interface and when unplugged it the sc> has slowly came up and then a normal reset solved everything
..
Now everything is working good...
Cheers guys..and thank you!
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Discussion started by: jsy
1 Replies
2. Solaris
Every time I would try to send a break to my T2000 I would get this
Debugging requested; hardware watchdog suspended.
c)ontinue, s)ync, r)eset?
I couldn't get into OBP.
Here's what I found to do...
sc> bootmode
Bootmode: normal
sc> bootmode reset_nvram
sc> bootmode... (3 Replies)
Discussion started by: mediis
3 Replies
3. Solaris
Hi,
I have forgot the sc and console login password in sun v125 server,
can anyone suggest me how to reset sc password in sun v125 server.
Thanks
Rjs (3 Replies)
Discussion started by: rajasekg
3 Replies
4. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
5. Solaris
Hi ,
How to reset ALOM/SC password for Solaris box Sun Fire T-200
Thanks (5 Replies)
Discussion started by: chetansingh23
5 Replies
6. Solaris
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Discussion started by: br1an
19 Replies
7. Solaris
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Discussion started by: rajasraf
1 Replies
8. Solaris
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
9. Hardware
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
10. Solaris
Hi all,
I got a v215 but the login credentials are unknown. I plug the serial management RS232-RJ45 and get the output on the terminal. I reseted NVRAM and battery but I can't use the default login still. After these operations the output from boot is as such ;
ALOM POST 1.0
Status =... (21 Replies)
Discussion started by: y33t
21 Replies
LEARN ABOUT DEBIAN
svn-bisect
SVN-BISECT(1) General Commands Manual SVN-BISECT(1)
NAME
svn-bisect - Bisect Subversion revisions to find a regression
SYNOPSIS
svn-bisect start [good_rev [bad_rev]]
svn-bisect {good|bad} [rev]
svn-bisect run command
svn-bisect reset
svn-bisect status
DESCRIPTION
svn-bisect helps to automate finding a bug or behavior change in a Subversion working copy. Given an initial "good" revision, with the
desired or original behavior, and a newer "bad" revision, with the undesired or modified behavior, svn-bisect will do a binary search
through the revision range to find which revision caused the change.
svn-bisect must be initialized in a working copy, with svn-bisect start. It also needs to be given at least one good revision (the base-
line) and one bad revision (known modified behavior) revision.
Sub-commands:
start Initializes or reinitializes svn-bisect; optionally takes good and bad revision parameters.
good rev
bad rev
Tells svn-bisect that a revision is good or bad, defining or narrowing the search space. If not specified, revision defaults to the
current revision in the working copy. svn-bisect will then update to a revision halfway between the new good and bad boundaries.
If this update crosses a point where a branch was created, it switches in or out of the branch.
reset Resets the working copy to the revision and branch where svn-bisect start was run. In the simple case this is equivalent to rm -r
.svn-bisect; svn update, but not if it has crossed branches, and not if you did not start at the HEAD revision. In any case,
svn-bisect never keeps track of mixed-revision working copies, so do not use svn-bisect in a working copy that will need to be
restored to mixed revisions.
status Prints a brief status message.
run command
Runs the bisection in a loop. You must have already defined initial good and bad boundary conditions. Each iteration through the
loop runs command as a shell command (a single argument, quoted if necessary) on the chosen revision, then marks the revision as
good or bad, based on the exit status of command.
EXAMPLES
Assume you are trying to find which revision between 1250 and 1400 caused the make check command to fail.
svn-bisect start 1250 1400
svn-bisect run 'make check'
svn-bisect reset
ENVIRONMENT
SVN The Subversion command-line program to call (default svn).
FILES
.svn-bisect
The directory containing state information, removed after a successful bisection.
SEE ALSO
git-bisect(1).
AUTHOR
Written by Robert Millan and Peter Samuelson, for the Debian Project (but may be used by others).
2009-10-22 SVN-BISECT(1)