09-17-2010
IIRC, the change from GUI to command line is handled by modification of /etc/init in the activation line for tty01.
Switching between the 12 ttys on the console keyboard is normally [ALT][Fkey] but getting out of the GUI on tty01 requires [CTRL][ALT][Fkey].
This User Gave Thanks to edfair For This Post:
9 More Discussions You Might Find Interesting
1. SCO
Why can I not login to the SCO GUI interface login screen? (1 Reply)
Discussion started by: qphillips
1 Replies
2. UNIX for Advanced & Expert Users
I was chatting with my teacher on how this could be a great tool for admins who are making the switch from GUI to CLI administration. I'm wondering, does this kind of tool exist? (4 Replies)
Discussion started by: Daemon-Killer
4 Replies
3. Programming
Hi,
the following code comes from Unix Linux dialog utility project.
Unfortunately, this project is no more actively maintained.
Unix Linux dialog utility is made of widget boxes.
One of them is mixedgauge.c
In the following example I would like to get rid of flickering
when run in... (0 Replies)
Discussion started by: jack2
0 Replies
4. Solaris
Hi all,
could you please tell me how to Change the subnet mask of interface aded:1 from ffffffc0 to ffffff80
regards
Krishna (7 Replies)
Discussion started by: murthy76
7 Replies
5. IP Networking
Hi all,
How an interface is selected based on the destination ip address.
Thanks in advance........ (5 Replies)
Discussion started by: vijaypdp2006
5 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Linux
the appliance is running on linux and accessible via http,telnet,etc.
When I do start-shell, I can access to its filesystem.
I am trying to change the interface name, currently is input1 to port-1.
It is not possible to change in WebGui or its CLI.
Possible to access its filesystem and change... (0 Replies)
Discussion started by: user51
0 Replies
dc(7) Miscellaneous Information Manual dc(7)
NAME
dc - serial line/mouse/keyboard
SYNOPSIS
controller dc0 at ibus0 slot 0 vector dcintr
DESCRIPTION
The dc serial line controller provides DECstation 2100, DECstation 3100, DECstation 5000, and DECstation 5100 computer systems with key-
board, mouse, and serial communications interfaces. The serial communications interfaces on the DECstation 2100 and DECstation 3100 provide
partial modem control. The serial communications interfaces on the DECstation 5000 provide full modem control. The device special file
/dev/tty01 on a DECstation 5100 provides full modem control, while the remaining ports provide no modem control at all. All serial commu-
nications interfaces operate at baud rates from B50 to B9600, excluding B200.
The dc ports are used as follows: Usage Graphics device keyboard at 4800 BPS Mouse or tablet at 4800 BPS Communications port 1 (w/modem
control)/local terminal Communications port 2 (w/modem control)/local terminal
On all systems except the DECstation 5100, serial port 2 is used for the system console port in server (that is, non-graphics) configura-
tions. On DECstation 5100s, the serial port labeled 3 on the back of the system is always the system console port. The serial system con-
sole port always operates at 9600 BPS, 8-bits, no parity; modem control is not supported.
RESTRICTIONS
Data communications equipment attached to the console serial port in server configurations must be set to 9600 BPS, 8-bits, no parity. The
scc driver enforces this restriction.
FILES
console terminal local terminal local terminal local terminal (DECstation 5100 only)
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
dc(7)