09-17-2010
IIRC, the change from GUI to command line is handled by modification of /etc/init in the activation line for tty01.
Switching between the 12 ttys on the console keyboard is normally [ALT][Fkey] but getting out of the GUI on tty01 requires [CTRL][ALT][Fkey].
This User Gave Thanks to edfair For This Post:
9 More Discussions You Might Find Interesting
1. SCO
Why can I not login to the SCO GUI interface login screen? (1 Reply)
Discussion started by: qphillips
1 Replies
2. UNIX for Advanced & Expert Users
I was chatting with my teacher on how this could be a great tool for admins who are making the switch from GUI to CLI administration. I'm wondering, does this kind of tool exist? (4 Replies)
Discussion started by: Daemon-Killer
4 Replies
3. Programming
Hi,
the following code comes from Unix Linux dialog utility project.
Unfortunately, this project is no more actively maintained.
Unix Linux dialog utility is made of widget boxes.
One of them is mixedgauge.c
In the following example I would like to get rid of flickering
when run in... (0 Replies)
Discussion started by: jack2
0 Replies
4. Solaris
Hi all,
could you please tell me how to Change the subnet mask of interface aded:1 from ffffffc0 to ffffff80
regards
Krishna (7 Replies)
Discussion started by: murthy76
7 Replies
5. IP Networking
Hi all,
How an interface is selected based on the destination ip address.
Thanks in advance........ (5 Replies)
Discussion started by: vijaypdp2006
5 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Linux
the appliance is running on linux and accessible via http,telnet,etc.
When I do start-shell, I can access to its filesystem.
I am trying to change the interface name, currently is input1 to port-1.
It is not possible to change in WebGui or its CLI.
Possible to access its filesystem and change... (0 Replies)
Discussion started by: user51
0 Replies
UBT(4) BSD Kernel Interfaces Manual UBT(4)
NAME
ubt -- USB Bluetooth driver
SYNOPSIS
ubt* at uhub? port ? configuration ? interface ?
DESCRIPTION
The ubt driver provides support for USB Bluetooth dongles to the Bluetooth protocol stack.
USB Bluetooth dongles provide two interfaces, both of which the ubt driver claims. The second interface is used for Isochronous data and
will have several alternate configurations regarding bandwidth consumption, which can be set using the hw.ubtN.config sysctl(8) variable.
The number of alternate configurations is indicated by the value in the hw.ubtN.alt_config variable, and the isoc frame size for the current
configuration is shown in the hw.ubtN.sco_rxsize and hw.ubtN.sco_txsize variables.
By default, configuration 0 is selected, which means that no bandwidth is used on the Isochronous interface and no SCO data can be sent.
Consult the Bluetooth USB specification at https://www.bluetooth.org/ for complete instructions on setting bandwidth consumption. The fol-
lowing extract may be useful as a general guidance though details may differ between manufacturers.
0 No active voice channels
1 One voice channel with 8-bit encoding
2 Two voice channels with 8-bit encoding, or one voice channel with 16-bit encoding.
3 Three voice channels with 8-bit encoding
4 Two voice channels with 16-bit encoding
5 Three voice channels with 16-bit encoding
SEE ALSO
bluetooth(4), uhub(4), sysctl(8)
HISTORY
This ubt device driver was originally a character device written by David Sainty and Lennart Augustsson. It was rewritten to support socket
based Bluetooth access for NetBSD 4.0 by Iain Hibbert.
CAVEATS
Isochronous data is seemingly not well supported over USB in the current system and to get SCO working, you may have to calculate the SCO
packet size that the stack will use. This is the sco_mtu value reported by the btconfig(8) command, and when combined with the SCO header (3
bytes) should fit exactly into an integer number of Isochronous data frames where the frame size is indicated by the 'hw.ubtN.sco_txsize'
sysctl variable.
For example: I want one voice channel (which is all that is supported, for now) so am using configuration #2, with a frame length of 17
bytes. This gives possible values of:
(17 * 1) - 3 = 14
(17 * 2) - 3 = 31
(17 * 3) - 3 = 48
(17 * 4) - 3 = 65
(17 * 5) - 3 = 82
etc.
btconfig(8) shows the maximum SCO payload as 64 bytes, so I am using the next smaller size of 48, to minimize the overhead of the 3 header
bytes.
The SCO packet size can be changed using the 'scomtu' option to btconfig(8).
The failure mode is that the USB Bluetooth dongle locks up though generally removal/reinsertion will clear the problem.
BUGS
The Isochronous configuration can only be changed when the device is not marked up.
BSD
August 27, 2006 BSD