say in this example of a ifconfig -a.
at times i do receive the output without the RUNNING word . what does this mean?
does indicate a network collision?
what is network collision - two or more tcp/udp connection trying to access the same network interface? say in this case ce1 ?
Last edited by Franklin52; 09-16-2010 at 03:15 AM..
Reason: Please use code tags!
Not sure if this is the right section for this. Move if necessary
Hey guys,
Just wanting to know if anyone has had a similar experience.
I have a FreeBSD 4.8 gateway machine with a dual boot win98/FreeBSD machine connected to it. When I'm in windows and playing a game, Diablo II or Star... (11 Replies)
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Hello,
I have been having a problem with printing to a network printer on my LAN, I am able to ping all ports from the server and the printer. Print request just stay in the print que the only way to print is from the parallel line to the server. Any ideas on what can be going wrong?? Lp sched is... (1 Reply)
Hi
I had installed Sun Solaris 10 on my dell vostro 1400.Problem is iam unable to mount the usb drives as there was no detections at all.And also iam unable to find my network interface or iam not able to install the network card.
If try to type ifconfig -a
It is showing only loop back... (4 Replies)
Hello everyone,
In a script, I am using SCP to copy huge file to another host.
scp -qrp hugefile.txt /opt/perf05/tmp
However, we have noticed that this file is not being copied. I am suspecting this was because we are losing connection while copying this... (1 Reply)
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Newbie with UNIX here.
Currently troubleshooting a UNIX terminal we have.
I determined it to be bad and swapped it out with a known good terminal. I went in and changed the IP address and host name to reflect the old terminal. Although now there is no connectivity.
I swapped out the NIC... (1 Reply)
Hi Guys,
I have two databases where I copy archivelog files from server A to server B frequently...yesterday we did the VM upgrade now...I am struggling to copy/ship the files from server A to server B...
I manually tested the file transfer but the big files, e.g 46M, stall. I can copy small... (2 Replies)
Oflate we are finding a few servers experiencing severe slowness. What would be the commands that I need to try to postmortem the situation? (3 Replies)
Discussion started by: ggayathri
3 Replies
LEARN ABOUT DEBIAN
gnunet-nat-server
GNUNET-NAT-SERVER(1) General Commands Manual GNUNET-NAT-SERVER(1)NAME
gnunet-nat-server - help GNUnet setup test network setup with NAT
SYNOPSIS
gnunet-nat-server [options] PORT
DESCRIPTION
Normal GNUnet end-users should not concern themselves with gnunet-nat-server. In fact, distributions are encouraged to consider not ship-
ping it at all. Running gnunet-nat-server's is similar to running hostlist servers: it is a special service to the community with special
requirements and no benefit to those running the service.
This program will listen on the specified PORT for incoming requests to test a peer's network connectivity. Incoming requests can ask it
to connect to a given IPv4 address (and port) using TCP or UDP and to send a 2-byte test message using the specified address. The program
can also be asked to send a "fake" ICMP response message to a given IPv4 address (for autonomous NAT traversal --- see the description in
the respective research paper).
The idea is that gnunet-nat-server will be run on some trusted hosts with unrestricted connectivity to allow GNUnet users to test their
network configuration. As written, the code allows any user on the Internet to cause the gnunet-nat-server to send 2-bytes of arbitrary
data to any TCP or UDP port at any address. We believe that this is generally harmless.
When running gnunet-nat-server, make sure to use a configuration that disables most NAT options but enables 'enable_nat_client' and sets
'internal_address' to the global IP address of your local host. Also, the gnunet-helper-nat-client should be installed locally and run
with root privileges (SUID), otherwise the gnunet-nat-server will not work properly.
Note that gnunet-nat-server could be run via gnunet-arm but typically is not. Also, the name of the host and port that gnunet-nat-server
is run on should be specified in the NATSERVER option in the [setup] section of the configuration file of hosts that are supposed to auto-
configure with this server.
OPTIONS -c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO gnunet-transport(1)GNUnet 25 Feb 2012 GNUNET-NAT-SERVER(1)