Sponsored Content
Full Discussion: Add route to solaris10
Operating Systems Solaris Add route to solaris10 Post 302452724 by msrkarthikeyan on Monday 13th of September 2010 01:04:33 AM
Old 09-13-2010
From the routing table of server 3, I can see that it already has a route to the server4 ce0 interface.

10.21.125.32 255.255.255.224 10.6.129.1 1500* 0 1 UG 1 0

10.21.125.32 => 10. 21.125.0010 0000
255.255.255.224 => 255.255.255.1110 0000
-----------------------------------------------------------------
From the last 5 host bits, we should know that the network 10.21.125.32/27 implies that the host IPs are from 10.21.125.32 to 10.21.125.63.

So You only need to add a route server4.

server 4
route add host 10.6.129.33 <appropriate gateway>

from the output you have provided its not clear what the gateway should be. If you can provide a small network diagram(if not full picture, atleast the one that shows cabling between the 2 servers) I might be able to help.

Your ping is failing now because the packets from server3 will reach server4 but server4 will not know how to respond as it does not have a route to server3.

good luck
 

10 More Discussions You Might Find Interesting

1. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies

2. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

3. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

4. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

5. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

6. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

7. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

8. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

9. Linux

Add persistent route in cent os 6.5

Hi , I have cent os 6.5 and am trying to make few routes permanent for bond: i have added two routes using below two commands : /sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.59.160.128 /sbin/route add -net 0.0.0.0 netmask 0.0.0.0 gw 49.44.52.90 post which route command output is... (5 Replies)
Discussion started by: omkar.jadhav
5 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 09:26 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy