09-09-2010
you need to ask your network person for the correct netmask and gateway.
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
4. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
5. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
6. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
9. Linux
Hi ,
I have cent os 6.5 and am trying to make few routes permanent for bond:
i have added two routes using below two commands :
/sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.59.160.128
/sbin/route add -net 0.0.0.0 netmask 0.0.0.0 gw 49.44.52.90
post which route command output is... (5 Replies)
Discussion started by: omkar.jadhav
5 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
ifscheme
IFSCHEME(8) Commands IFSCHEME(8)
NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS
-v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO
interfaces(5) ifup(8) ifdown(8)
DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)