09-09-2010
you need to ask your network person for the correct netmask and gateway.
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
4. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
5. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
6. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
9. Linux
Hi ,
I have cent os 6.5 and am trying to make few routes permanent for bond:
i have added two routes using below two commands :
/sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.59.160.128
/sbin/route add -net 0.0.0.0 netmask 0.0.0.0 gw 49.44.52.90
post which route command output is... (5 Replies)
Discussion started by: omkar.jadhav
5 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT NETBSD
pcap_compile
PCAP_COMPILE(3) Library Functions Manual PCAP_COMPILE(3)
NAME
pcap_compile - compile a filter expression
SYNOPSIS
#include <pcap/pcap.h>
int pcap_compile(pcap_t *p, struct bpf_program *fp,
const char *str, int optimize, bpf_u_int32 netmask);
DESCRIPTION
pcap_compile() is used to compile the string str into a filter program. See pcap-filter(7) for the syntax of that string. program is a
pointer to a bpf_program struct and is filled in by pcap_compile(). optimize controls whether optimization on the resulting code is per-
formed. netmask specifies the IPv4 netmask of the network on which packets are being captured; it is used only when checking for IPv4
broadcast addresses in the filter program. If the netmask of the network on which packets are being captured isn't known to the program,
or if packets are being captured on the Linux "any" pseudo-interface that can capture on more than one network, a value of PCAP_NET-
MASK_UNKNOWN can be supplied; tests for IPv4 broadcast addreses will fail to compile, but all other tests in the filter program will be OK.
RETURN VALUE
pcap_compile() returns 0 on success and -1 on failure. If -1 is returned, pcap_geterr() or pcap_perror() may be called with p as an argu-
ment to fetch or display the error text.
SEE ALSO
pcap(3), pcap_setfilter(3), pcap_freecode(3), pcap_geterr(3), pcap-filter(7)
5 April 2008 PCAP_COMPILE(3)