09-06-2010
And one with VCS? Is it available?
10 More Discussions You Might Find Interesting
1. Solaris
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies
2. Solaris
Hi,
Quick question if anyone knows this. Is there a command I can use in Veritas Volume manager on Solaris that will tell me what the name of the SAN I am connected to? We have a number of SANs so I am unsure which one my servers are connected to. Thanks. (13 Replies)
Discussion started by: gwhelan
13 Replies
3. Filesystems, Disks and Memory
whats the command line to find vxvm (veritas volume manager) version installed in solaris OS? (3 Replies)
Discussion started by: na75369
3 Replies
4. Solaris
Hi Friends,
This is suresh reddy. Recently i download veritas cluster & volume manager package from internet. I didn't found any key inside the package. If any body having the VxVM key kindly send to me.
mail id: cvsureshreddy@gmail.com
Regards,
C V Suresh Reddy (1 Reply)
Discussion started by: suresha2lu
1 Replies
5. Solaris
Hi,
I just wanted to know, if VCS simulator (For Solaris) is available for free ? I will be running that on my Windows XP.
If somebody have, please share the link.
Regards
---------- Post updated at 08:34 AM ---------- Previous update was at 07:43 AM ----------
I was able to get it... (0 Replies)
Discussion started by: solaris_1977
0 Replies
6. Linux
I ve read the documentation and tried downloading from code nsnam org to no avail, though not very good in linux, what do i do? (4 Replies)
Discussion started by: OSISIOMA
4 Replies
7. Solaris
This is going to mean nothing to most....
I'm working on a E4500 server running Solaris 2.5.1 and VXVM 2.5.5 :eek:
I've replaced the rootmirror and would like to monitor progress of the resync
It's only a 2Gb /partition so it shouldn't take too long.
In later versions
vxtask list
... (5 Replies)
Discussion started by: Martincorneuk
5 Replies
8. Solaris
Hello all,
i try to allocate the same LUN to two server (or more in the future)
i use solaris 10, vxvm (vxfs) for data and solaris zones and EMC DMX-4, i try to migrate solaris zones between servers in case of problem.
and this is what i want to do
- affect LUN to srv00124 and srv10155
-... (5 Replies)
Discussion started by: mat_solaris
5 Replies
9. Solaris
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
Discussion started by: Zam_1234
3 Replies
10. Solaris
Hello,
I was assigned some Solaris machines and need to patch them to N-1, where N is the latest OS realease, which means, upgrade till one version before the latest one.
I do not now a lot about Solaris. What I only know is that need to make use of live upgrade and be careful with VxVM... (4 Replies)
Discussion started by: feroccimx
4 Replies
pfto(7) Miscellaneous Information Manual pfto(7)
NAME
pfto - Powerfail Timeout
DESCRIPTION
HP-UX SCSI disk device drivers have a timeout facility that detects non-responding disks. VxVM uses this mechanism in its Powerfail Time-
out (pfto) feature. You can specify a timeout value for individual VxVM disks using the vxdisk command (see the EXAMPLES section below).
If a disk fails to respond in the specified timeout period, the driver receives a timer interrupt.
pfto values are persistent across reboots, that is, after the pfto value is set, it remains in effect until you explicitly change it. If
dynamic multipathing is enabled, the pfto value set on a disk applies to each path of a multipath disk device.
The pfto value is in seconds. If pfto is not specified, or is zero, the timeout period is 30 seconds. Both the vxdisk and vxprint commands
display the current pfto value for a disk.
EXAMPLES
Use the following command to set the value of pfto to 30 seconds on disk01:
vxdisk -g rootdg set disk01 pfto=30
Use either of the following commands to display the pfto value on the VxVM disk disk01:
vxdisk list disk01
vxprint -l disk01
EXIT CODES
Setting the pfto value on a non-VxVM disk returns an error.
SEE ALSO
vxdisk(1M), vxprint(1M)
VxVM 5.0.31.1 24 Mar 2008 pfto(7)