I use the following command dk -k and get the following output:
Filesystem kbytes used avail capacity Mounted on
/dev/dsk/c0t0d0s0 1587078 56546 1482920 4% /
/dev/dsk/c0t0d0s6 1984230 926199 998505 49% /usr
/proc 0 0 0 ... (1 Reply)
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Hi, I'm trying to mount a usb drive but the path /dev/sda1 does not show up under /dev when I plug in the usb device.
In fact I see no differences under /dev before and after I plugin my usb drive.
Any ideas why the system is not recognizing the usb drive and how to fix?
This is on a... (3 Replies)
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Hi,
How can i check that i am using RAW devices for storage in my AIX machine...
Also after adding a LUN from storage to a aix host, when i check /dev in the host, i can see both rhdisk and hdisk with same number
eg:
dcback1(root):/dev>ls -lrt | grep disk12
crw------- 1 root ... (4 Replies)
Hello AIXians,
I can't boot my AIX, it hangs and stops at the code error: 0518
After searching google, I knew the problem is due to problems in File Systems.
So the solution is booting from any bootable media, then run these commands in maintenance mode:
#fsck -y /dev/hd4
#fsck -y... (3 Replies)
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
sgdisk -n... (12 Replies)
AIX Version 6.1 and 7.1.
I understand that when the OS initially creates the FS and inodes, its pretty strict, but not always tuned to a 1:1 ratio. I see the same thing when adding a whole disk LV to a separate device.
It seems that when we expand a filesystem the inodes don't get tuned... (5 Replies)
Hi,
Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)