08-31-2010
I do not have a network. I like the idea about using an ethernet cable between the 2 machines but my Windows computer is connected to the internet via a LAN cable and I cannot connect my Linux box to internet (even if I want to). So, how can I still use an ethernet cable if one of my computers is already using it to access internet?
6 More Discussions You Might Find Interesting
1. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
2. Red Hat
:confused:Hello All,
We are trying to install RHEL6 via USB using KICKSTART installation.
We had following configuration:
Below is the entry of isolinux.cfg file :
menu label ^Kickstart Installation:via USB
kernel vmlinuz
append initrd=initrd.img ks=cdrom:/ks.cfg
Below is the entry... (2 Replies)
Discussion started by: NIMISH AGARWAL
2 Replies
3. Ubuntu
I am trying to dual boot on an external USB 500GB drive using my laptop.I have Windows 7 installed and booting on 1st partition 230GB now as active primary, 2nd partition is 100GB as primary, and 3rd partition is 135GB as primary. I was intending on installing Ubuntu onto the 2nd partition. I read... (12 Replies)
Discussion started by: coolecho
12 Replies
4. Filesystems, Disks and Memory
My CD drive isn't working. So, is there any way to create windows recovery/repair software in flash drive/usb. This is the s/w which we use if system fails to boot. (1 Reply)
Discussion started by: ravisingh
1 Replies
5. Boot Loaders
I successfully created a bootable windows 7 repair usb.
Please clarify me:
I rebooted my system via USB. windows repair window appeared. There were 5 options. I opted 'windows memory diagnostic' and it worked fine. There was an option named 'start up repair'. This option can be used if windows... (2 Replies)
Discussion started by: ravisingh
2 Replies
6. HP-UX
Greetings.
Seeking guidance on adding a USB barcode reader (BCR) to an HP c3750 workstation with HP-UX 11.11 which is essentially configuring X windows to accept input from both a primary keyboard and a secondary keyboard that happens to be the BCR.
Historically, I have successfully added a BCR... (2 Replies)
Discussion started by: mnkaltenbach
2 Replies
LEARN ABOUT MINIX
liebert
LIEBERT(8) NUT Manual LIEBERT(8)
NAME
liebert - Driver for Liebert contact-closure UPS equipment
NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
You may have to build another cable with DTR connected through to the UPS for it to work.
There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
fundamental limitation of any contact-closure driver.
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 LIEBERT(8)