08-31-2010
Do you have a home network set up? If not, could you run a loopback ethernet cable between your Windows machine and your Linux one? I think that'd be more straightforward than trying to get a USB-USB interface working, particularly since these devices(they contain electronics, not just wires) usually act like network interfaces anyway.
6 More Discussions You Might Find Interesting
1. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
2. Red Hat
:confused:Hello All,
We are trying to install RHEL6 via USB using KICKSTART installation.
We had following configuration:
Below is the entry of isolinux.cfg file :
menu label ^Kickstart Installation:via USB
kernel vmlinuz
append initrd=initrd.img ks=cdrom:/ks.cfg
Below is the entry... (2 Replies)
Discussion started by: NIMISH AGARWAL
2 Replies
3. Ubuntu
I am trying to dual boot on an external USB 500GB drive using my laptop.I have Windows 7 installed and booting on 1st partition 230GB now as active primary, 2nd partition is 100GB as primary, and 3rd partition is 135GB as primary. I was intending on installing Ubuntu onto the 2nd partition. I read... (12 Replies)
Discussion started by: coolecho
12 Replies
4. Filesystems, Disks and Memory
My CD drive isn't working. So, is there any way to create windows recovery/repair software in flash drive/usb. This is the s/w which we use if system fails to boot. (1 Reply)
Discussion started by: ravisingh
1 Replies
5. Boot Loaders
I successfully created a bootable windows 7 repair usb.
Please clarify me:
I rebooted my system via USB. windows repair window appeared. There were 5 options. I opted 'windows memory diagnostic' and it worked fine. There was an option named 'start up repair'. This option can be used if windows... (2 Replies)
Discussion started by: ravisingh
2 Replies
6. HP-UX
Greetings.
Seeking guidance on adding a USB barcode reader (BCR) to an HP c3750 workstation with HP-UX 11.11 which is essentially configuring X windows to accept input from both a primary keyboard and a secondary keyboard that happens to be the BCR.
Historically, I have successfully added a BCR... (2 Replies)
Discussion started by: mnkaltenbach
2 Replies
LO(4) Kernel Interfaces Manual LO(4)
NAME
lo - software loopback network interface
SYNOPSIS
/sys/conf/SYSTEM:
NLOOP 1 # loop-back pseudo-device
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communica-
tion. As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it
is to be used. These addresses may be set or changed with the SIOCSIFADDR ioctl. The loopback interface should be the last interface con-
figured, as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first
unless no hardware interfaces exist.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
intro(4N), inet(4F), ns(4F)
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
3rd Berkeley Distribution August 1, 1987 LO(4)