08-31-2010
Do you have a home network set up? If not, could you run a loopback ethernet cable between your Windows machine and your Linux one? I think that'd be more straightforward than trying to get a USB-USB interface working, particularly since these devices(they contain electronics, not just wires) usually act like network interfaces anyway.
6 More Discussions You Might Find Interesting
1. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
2. Red Hat
:confused:Hello All,
We are trying to install RHEL6 via USB using KICKSTART installation.
We had following configuration:
Below is the entry of isolinux.cfg file :
menu label ^Kickstart Installation:via USB
kernel vmlinuz
append initrd=initrd.img ks=cdrom:/ks.cfg
Below is the entry... (2 Replies)
Discussion started by: NIMISH AGARWAL
2 Replies
3. Ubuntu
I am trying to dual boot on an external USB 500GB drive using my laptop.I have Windows 7 installed and booting on 1st partition 230GB now as active primary, 2nd partition is 100GB as primary, and 3rd partition is 135GB as primary. I was intending on installing Ubuntu onto the 2nd partition. I read... (12 Replies)
Discussion started by: coolecho
12 Replies
4. Filesystems, Disks and Memory
My CD drive isn't working. So, is there any way to create windows recovery/repair software in flash drive/usb. This is the s/w which we use if system fails to boot. (1 Reply)
Discussion started by: ravisingh
1 Replies
5. Boot Loaders
I successfully created a bootable windows 7 repair usb.
Please clarify me:
I rebooted my system via USB. windows repair window appeared. There were 5 options. I opted 'windows memory diagnostic' and it worked fine. There was an option named 'start up repair'. This option can be used if windows... (2 Replies)
Discussion started by: ravisingh
2 Replies
6. HP-UX
Greetings.
Seeking guidance on adding a USB barcode reader (BCR) to an HP c3750 workstation with HP-UX 11.11 which is essentially configuring X windows to accept input from both a primary keyboard and a secondary keyboard that happens to be the BCR.
Historically, I have successfully added a BCR... (2 Replies)
Discussion started by: mnkaltenbach
2 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD