Sponsored Content
Operating Systems Linux Ubuntu Ubuntu 10.04 - Unable to connect to Cisco VPN Post 302449701 by morningSunshine on Tuesday 31st of August 2010 08:32:07 AM
Old 08-31-2010
Thanks. I have already checked this option. I observed that unless I check it, the new VPN conn name does not appear in the VPN Connections.

I select it but it gives 'The VPN connection 'VPN' failed'.?
 

9 More Discussions You Might Find Interesting

1. IP Networking

Cisco vpn client

Who in the 64 ubuntu adopted cisco vpn client on the wireless network I downloaded the cisco vpn client for linux but run vpn_install make file when an error in cisco with the help of the document read in half a day, nor do I know this vpn client in the 64 systems in use. Who can help me, a... (1 Reply)
Discussion started by: Eason
1 Replies

2. IP Networking

Setup Dial In VPN on Cisco Router

Hello, Does anyone know where I can find configuration information on setting up a dial in VPN on Cicso IOS for a bunch of servers. Could not seem to find anything in search engines. Thanks (0 Replies)
Discussion started by: photon
0 Replies

3. Shell Programming and Scripting

continue after connecting to cisco vpn

Hi all, This will save me a tremendous amount of time if i can get this script working. I have alot of sites i need to connect to using cisco vpn and then ssh onto servers to retrieve some info. Its all repetitative and it needs scripted. what i have done so far is put this into a script. ... (0 Replies)
Discussion started by: borderblaster
0 Replies

4. Solaris

Cisco IOS VPN server IKE

How do I tell if Cisco IOS VPN server IKE is running on my solaris 10 system (1 Reply)
Discussion started by: pgsanders
1 Replies

5. Red Hat

cisco anyconnect VPN client installation??

Anyone had installed Cisco AnyConnect VPN client on RedHat5.3 EL or CentOS 5.3? I tried on CentOS 5.3 but always getting host unreachable error. Same for windows xp works fine. The error log reports: Sep 1 19:14:03 localhost vpnagent: Function: tableCallbackHandler File: RouteMgr.cpp Line:... (3 Replies)
Discussion started by: zing_foru
3 Replies

6. UNIX for Dummies Questions & Answers

Problem when I try to Install a Client VPN Cisco

Hi Gurus of UNIX, I have a problem when I try to install a software VPN Cisco in Laptop (HP530). I do the following procedures: Part 2 - VPN Client Compilation We will now set up the vpn client. As there is no official Cisco VPN Client for OpenSolaris X86 available, we will use vpnc.... (1 Reply)
Discussion started by: andresguillen
1 Replies

7. IP Networking

Cisco VPN pcf and OpenVPN

I was given my pcf file to login to work from home and wanted to use OpenVPN instead of the Cisco VPN client software. Can I use this pcf file with OpenVPN? I attempted to use vpnc: http://wiki.centos.org/HowTos/vpnc but it just times out ?? (2 Replies)
Discussion started by: metallica1973
2 Replies

8. IP Networking

Cisco VPN server and client - connection drop

I have a Cisco 1841 router configured as Easy VPN Server. Here is the configuration of the router: Cisco# Cisco#show running-config Building configuration... Current configura - Pastebin.com I have a Centos 5.7 server with installed Cisco VPN client for Linux. The client successfully... (0 Replies)
Discussion started by: rcbandit
0 Replies

9. IP Networking

Cisco 3750 Switch ASA VPN Routing

Hi,I want connect my ASA 5510 firewall to a 3750 switch with RIP routing. Unfortunately,I am having issues passing the VPN subnet through rip to the 3750.I don't understand how the routing table is populated on the ASA. Any suggestions? (0 Replies)
Discussion started by: Ayaerlee
0 Replies
UBUNTU-BUILD(1) 					      General Commands Manual						   UBUNTU-BUILD(1)

NAME
ubuntu-build - command-line interface to Launchpad build operations SYNOPSIS
ubuntu-build <srcpackage> <release> <operation> DESCRIPTION
ubuntu-build provides a command line interface to the Launchpad build operations. OPERATIONS
Listed below are the available operations for ubuntu-build: status Outputs the build status of the package on Launchpad on all architectures. retry Requests that the package has another attempt at rebuilding from source. This will only work if the package has Failed to build on Launchpad. rescore Requests that the package's build priority be raised in the build queue. Only members of the Launchpad build administrators may issue this operation, and it may only be performed on packages which Need building. OPTIONS
Listed below are the command line options for ubuntu-build: -h or --help Display a help message and exit. Retry and rescore options: These options may only be used with the 'retry' and 'rescore' operations. -a ARCHITECTURE, --arch=ARCHITECTURE Rebuild or rescore a specific architecture. Valid architectures include: amd64, sparc, powerpc, i386, armel, armhf, ia64, lpia, hppa. Batch processing: These options and parameter ordering is only available in --batch mode. Usage: ubuntu-build --batch [options] <package>... --batch Enable batch mode --series=SERIES Selects the Ubuntu series to operate on (default: current development series) --retry Retry builds (give-back). --rescore=PRIORITY Rescore builds to <priority>. --arch2=ARCHITECTURE Affect only 'architecture' (can be used several times). Valid architectures are: amd64, sparc, powerpc, i386, armel, armhf, ia64, lpia, hppa. AUTHORS
ubuntu-build was written by Martin Pitt <martin.pitt@canonical.com>, and this manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>. Both are released under the terms of the GNU General Public License, version 3 or (at your option) any later version. ubuntu-dev-tools June 2010 UBUNTU-BUILD(1)
All times are GMT -4. The time now is 10:49 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy