Running Solaris 9 with SVM. I'm not that familiar with it, but metastat output gives "needs maintenance" message on 2 of the mirrors. There are no errors in /var/adm/messages. What do I need to do to fix this error? Thanks. (14 Replies)
My company is running a solaris 2.7 machine. The machine is getting slow recently. I have no expert in solaris. Please help.
I checked the log in /var/adm/message:
I also checked with the command iostat -nE. It returns:
Metastat returns the followings:
What should i do now?... (10 Replies)
HI,
I added by error to a submirror some disks :
metattach d53 c2t90d0s0 c2t90d1s0 ... instead of doing a stripe by disk (like that) :
metattach d53 c2t90d0s0
metattach d53 c2t90d1s0
..
then, I did a growfs -M to expand FS and the size isn't correct.
I tried to launch a... (1 Reply)
Hi Guys!
I am facing Problem with SVM I mention the problem below:
I have Sunfire V210 machine and the partitions are as follows:
Part Tag Flag Cylinders Size Blocks
0 root wm 0 - 6134 29.77GB (6135/0/0) 62429760
1 swap wu ... (1 Reply)
Greetings
How can i restore metastat db after a solaris upgrade (9 to 10)?
will it work if i save and restore /etc/vfstab and /etc/lvm/md.cf file?
root@netad# metastat
d35: Mirror
Submirror 0: d38
State: Okay
Submirror 1: d39
State: Okay
Pass:... (2 Replies)
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
hi all
please help me with the following
i am new to solaris
i want to umount /test mount point and make it 8gb each i.e. /test1 and /test2 and using SVM wants to make RAID5
bash-3.00# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c0t0d0s0 6.9G ... (2 Replies)
Hi
I am new to live upgrade.
I would like to tell you about my new setup, where my boot disk(c0d0) is mirrored with secondary disk(c0d1). I have remove the secondary whole disk(C0d1) from the mirror, so that I can do live upgrade on this secondary disk.
I have done live upgrade on s0 partition... (3 Replies)
Hello Gurus,
I am setting up a V240 with solaris 10 for learning purpose. I have 4 x 36Gb disk installed and I now want to install SVM just tp learn this disk management utility. What I want to know is where do I look for the SVM pkg ?
is this the right command pkgchk -L SUNWsvm . Can anyone... (3 Replies)
Discussion started by: Moh
3 Replies
LEARN ABOUT SUNOS
mdlogd
mdlogd(1M) System Administration Commands mdlogd(1M)NAME
mdlogd - Solaris Volume Manager daemon
SYNOPSIS
mdlogd
DESCRIPTION
mdlogd implements a simple daemon that watches the system console looking for messages written by the Solaris Volume Manger. When a Solaris
Volume Manager message is detected, mdlogd sends a generic SNMP trap.
To enable traps, you must configure mdlogd into the SNMP framework. See Solaris Volume Manager Administration Guide.
USAGE
mdlogd implements the following SNMP MIB:
SOLARIS-VOLUME-MGR-MIB DEFINITIONS ::= BEGIN
IMPORTS
enterprises FROM RFC1155-SMI
DisplayString FROM SNMPv2-TC;
-- Sun Private MIB for Solaris Volume Manager
sun OBJECT IDENTIFIER ::= { enterprises 42 }
sunSVM OBJECT IDENTIFIER ::= { sun 104 }
-- this is actually just the string from /dev/log that
-- matches the md: regular expressions.
-- This is an interim SNMP trap generator to provide
-- information until a more complete version is available.
-- this definition is a formalization of the old
-- Solaris DiskSuite mdlogd trap mib.
svmOldTrapString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the matched string that
was obtained from /dev/log."
::= { sunSVM 1 }
-- SVM Compatibility ( error trap )
svmNotice TrapTRAP-TYPE
ENTERPRISE sunSVM
VARIABLES { svmOldTrapString }
DESCRIPTION
"SVM error log trap for NOTICE.
This matches 'NOTICE: md:'"
::= 1
svmWarningTrap TRAP-TYPE
ENTERPRISE sunSVM
VARIABLES { svmOldTrapString }
DESCRIPTION
"SVM error log trap for WARNING..
This matches 'WARNING: md:'"
::= 2
svmPanicTrap TRAP-TYPE
ENTERPRISE sunSVM
VARIABLES { svmOldTrapString }
DESCRIPTION
"SVM error log traps for PANIC..
This matches 'PANIC: md:'"
::= 3
END
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWlvma, SUNWlvmr |
+-----------------------------+-----------------------------+
|Interface Stability |Obsolete |
+-----------------------------+-----------------------------+
SEE ALSO snmpdx(1M), attributes(5)
Solaris Volume Manager Administration Guide
SunOS 5.10 3 Jun 2004 mdlogd(1M)