|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
unmount the partition
Post 302448558 by prakashkumar41 on Thursday 26th of August 2010 10:09:51 AM
08-26-2010
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
2. AIX
hi all,
I am new to AIX as well as UNIX also ,i have a question
One of my program has created a new filesystem on the system.....
df shows :
/dev/fslv04 2031616 2030648 1% 3 1% /replicas/source
when i tried to umount the above filesystem by
umount... (3 Replies)
Discussion started by: vamshi_k
3 Replies
3. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
4. Filesystems, Disks and Memory
Hi,
I know that if we need to unmount a device, we use the command umount mount-point, example 'umount /tmp/mount1'
But We can also unmount the device with device name example 'umount /dev/hda6'.
NOTE: I think in RHEL3 we cannot unmount with device name. Correct me if I am wrong.
What... (1 Reply)
Discussion started by: praveen_b744
1 Replies
5. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
6. Solaris
I have installed Solaris 11 Express on my machine, created a raidz2 zpool named shares and set up sharing (zfs set sharesmb=on shares). I also created a script for automatic backuping using snapshots.
Everything worked fine. But yesterday I tried recovering from one of those backuped snapshots:... (1 Reply)
Discussion started by: RychnD
1 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Shell Programming and Scripting
As stated, I am looking into keeping my backup drive unmounted in normal windows use. Partly this is to address threats like cryptolocker. Since one of my backup drives is an internal drive, it will not likely afford any protection from such a threat. I am thinking of adding code to my rsync script... (5 Replies)
Discussion started by: LMHmedchem
5 Replies
10. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT LINUX
hd
HD(4) Linux Programmer's Manual HD(4) NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)