08-24-2010
Quote:
Originally Posted by
semash!
Hey Corona688,
You were right, the driver '8139too' was blacklisted from modprobe, i don't know the reason.
Probably because they're mutually exclusive. A card can only use one of them, picking the wrong one will stop it from working, and there's no way for the kernel to tell which it needs until it's too late. You have to blacklist one to guarantee the correct one gets loaded first.
If it's not being used, you might want to blacklist 8139cp.
10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Discussion started by: adrienb
2 Replies
2. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ? :confused:
Thanks a lot for your help,
Fabien (5 Replies)
Discussion started by: unclefab
5 Replies
5. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
6. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
7. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
8. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
9. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
10. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies