Sponsored Content
Full Discussion: Error LED showing on E250
Operating Systems Solaris Error LED showing on E250 Post 302447815 by incredible on Tuesday 24th of August 2010 11:23:18 AM
Old 08-24-2010
Are you able to do a cold boot for the server? Prior to that ensure that the PSUs are ok.
If cold boot still does not work, you may need to check into the console message or boot the system in diag mode to go deeper. alternatively, perform a obdiag or POST test.
 

10 More Discussions You Might Find Interesting

1. Solaris

E250 - need to access it

Hi, We have an E250 which we need to access to install solaris 10 for a communigate trial. We only have the server itself, no cables or anything and im struggling to gain access. It has a RSC card, that i have learned, but a db25-db9 cable doesn't seem to bring anything up in telnet on... (11 Replies)
Discussion started by: e250user
11 Replies

2. Gentoo

Uses for a Sun e250?

We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be... (9 Replies)
Discussion started by: kccrusher
9 Replies

3. Solaris

mailx -s is showing an error

Error is like /users/d12381/check.sh: mail_sysadmin@mycompany: not found Plz help me to sort out this issue (6 Replies)
Discussion started by: Renjesh
6 Replies

4. Solaris

tar -xvf is showing error

Hi, When i am trying to untar a file for installation its showing an error like tar -xvf te_agent__sparc.en_tar.gz tar: directory checksum error Please help me to solve this issue........... (10 Replies)
Discussion started by: Renjesh
10 Replies

5. HP-UX

Error alert keep showing at console

Hi, I would like to ask for your help. I tried to log in through console to my server HP-UX 10.20 but I keep receiving error message as below: Vxfs: mesg 001: vx_nospace -/dev/vg02/lvol6 file system full Vxfs: mesg 001: vx_nospace - /dev/vg02/lvol9 file system full How should I stop this... (4 Replies)
Discussion started by: yeazas
4 Replies

6. Solaris

fmthard showing error with prtvtoc

Hi all, I am trying to use the disk for mirror where in the mirror disk is of 160 gb and the rootdisk is of 80 gb. when i am trying to write the vtoc i am getting below error i tried the below command #prtvtoc /dev/rdsk/c0t0d0s0 |fmthard -s -/dev/rdsk/c0t2d0s0 and got below ... (26 Replies)
Discussion started by: kumarmani
26 Replies

7. Solaris

ultra 10 showing Date ERROR

ultra 10 showing date error. it showing date --:--:1967 frequently.sometimes it shows correct date. (3 Replies)
Discussion started by: yesquery
3 Replies

8. Shell Programming and Scripting

command showing error

Hi, I have an command which find the files modified within last 8 days and then after selecting the files from the location it make the tar format and send it to the specified destination ...now I want that this task to be automative ..that is it should happen after every 5 minutes ...for that... (3 Replies)
Discussion started by: NARESH SAXENA
3 Replies

9. Linux

Disk is predictive failure but LED is showing green.

Hi Linux Team we use hpacucli ctrl all show config command find out the failure disk. Here command output is showing predictive failure but The Datacenter team are unable to find the correct failure disk. From Datacenter all LEDs are showing green. Datacenter asks us to blink the LED. How... (2 Replies)
Discussion started by: Naveen.6025
2 Replies

10. Shell Programming and Scripting

Showing error

if ; then rm -rf "${x}"_"${y}"_abc_pqr.dat error: `then' unmatchedCan anyone please help me in correcting it. Please use code tags next time for your code and data. Thanks (2 Replies)
Discussion started by: D_Sethi
2 Replies
dr(7d)								      Devices								    dr(7d)

NAME
dr, drmach, ngdr, ngdrmach - Sun Enterprise 10000 dynamic reconfiguration driver SYNOPSIS
dr drmach ngdr ngdrmach DESCRIPTION
The dynamic reconfiguration (DR) driver consists of a platform-independent driver and a platform-specific module. The DR driver uses stan- dard features of the Solaris operating environment whenever possible to control DR operations and calls the platform specific module as needed. The DR driver creates minor nodes in the file system that serve as attachment points for DR operations. The DR driver provides a pseudo-driver interface to sequence attach and detach operations on system boards using file system entry points referred to as "attachment points." The attachment point form depends on the platform. Sun Enterprise 10000 Server On the Sun Enterprise 10000 server, the DR driver consists of a platform-independent driver (ngdr) and a platform-specific module (ngdr- mach). The domain configuration server (DCS) accepts DR requests from the system services processor (SSP) and uses the libcfgadm(3LIB) interface to initiate the DR operation. After the operation is performed, the results are returned to the SSP. For more information about the DCS on the Sun Enterprise 10000, refer to the dcs(1M) man page and the Sun Enterprise 10000 Dynamic Reconfiguration User Guide. The DR driver creates physical attachment points for system board slots that takes the following form: /devices/pseudo/ngdr@0:SBx Where x represents the slot number (0 to 15) for a particular board. The cfgadm_sbd(1M) plugin creates dynamic attachment points that refer to components on system boards, including CPUs, memory, or I/O devices. Refer to the cfgadm_sbd(1M) man page for more details. SEE ALSO
cfgadm_sbd(1M), ioctl(2), libcfgadm(3LIB) Sun Enterprise 10000 Dynamic Reconfiguration User Guide SunOS 5.11 29 Sep 2003 dr(7d)
All times are GMT -4. The time now is 12:44 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy