JOT(1)							    BSD General Commands Manual 						    JOT(1)

NAME

     jot -- print sequential or random data

SYNOPSIS

     jot [-cnr] [-b word] [-w word] [-s string] [-p precision] [reps [begin [end [s]]]]

DESCRIPTION

     The jot utility is used to print out increasing, decreasing, random, or redundant data, usually numbers, one per line.

     The following options are available:

     -r      Generate random data instead of the default sequential data.

     -b word
	     Just print word repetitively.

     -w word
	     Print word with the generated data appended to it.  Octal, hexadecimal, exponential, ASCII, zero padded, and right-adjusted represen-
	     tations are possible by using the appropriate printf(3) conversion specification inside word, in which case the data are inserted
	     rather than appended.

     -c      This is an abbreviation for -w %c.

     -s string
	     Print data separated by string.  Normally, newlines separate data.

     -n      Do not print the final newline normally appended to the output.

     -p precision
	     Print only as many digits or characters of the data as indicated by the integer precision.  In the absence of -p, the precision is
	     the greater of the precisions of begin and end.  The -p option is overridden by whatever appears in a printf(3) conversion following
	     -w.

     The last four arguments indicate, respectively, the number of data, the lower bound, the upper bound, and the step size or, for random data,
     the seed.	While at least one of them must appear, any of the other three may be omitted, and will be considered as such if given as - or as
     an empty string.  Any three of these arguments determines the fourth.  If four are specified and the given and computed values of reps con-
     flict, the lower value is used.  If fewer than three are specified, defaults are assigned left to right, except for s, which assumes a
     default of 1 or -1 if both begin and end are given.

     Defaults for the four arguments are, respectively, 100, 1, 100, and 1, except that when random data are requested, the seed, s, is picked
     randomly.	The reps argument is expected to be an unsigned integer, and if given as zero is taken to be infinite.	The begin and end argu-
     ments may be given as real numbers or as characters representing the corresponding value in ASCII.  The last argument must be a real number.

     Random numbers are obtained through arc4random(3) when no seed is specified, and through random(3) when a seed is given.  When jot is asked
     to generate random integers or characters with begin and end values in the range of the random number generator function and no format is
     specified with one of the -w, -b, or -p options, jot will arrange for all the values in the range to appear in the output with an equal prob-
     ability.  In all other cases be careful to ensure that the output format's rounding or truncation will not skew the distribution of output
     values in an unintended way.

     The name jot derives in part from iota, a function in APL.

   Rounding and truncation
     The jot utility uses double precision floating point arithmetic internally.  Before printing a number, it is converted depending on the out-
     put format used.

     If no output format is specified or the output format is a floating point format ('E', 'G', 'e', 'f', or 'g'), the value is rounded using the
     printf(3) function, taking into account the requested precision.

     If the output format is an integer format ('D', 'O', 'U', 'X', 'c', 'd', 'i', 'o', 'u', or 'x'), the value is converted to an integer value
     by truncation.

     As an illustration, consider the following command:

	   $ jot 6 1 10 0.5
	   1
	   2
	   2
	   2
	   3
	   4

     By requesting an explicit precision of 1, the values generated before rounding can be seen.  The .5 values are rounded down if the integer
     part is even, up otherwise.

	   $ jot -p 1 6 1 10 0.5
	   1.0
	   1.5
	   2.0
	   2.5
	   3.0
	   3.5

     By offsetting the values slightly, the values generated by the following command are always rounded down:

	   $ jot -p 0 6 .9999999999 10 0.5
	   1
	   1
	   2
	   2
	   3
	   3

     Another way of achieving the same result is to force truncation by specifying an integer format:

	   $ jot -w %d 6 1 10 0.5

EXIT STATUS

     The jot utility exits 0 on success, and >0 if an error occurs.

EXAMPLES

     The command
	   jot - 1 10

     prints the integers from 1 to 10, while the command
	   jot 21 -1 1.00

     prints 21 evenly spaced numbers increasing from -1 to 1.  The ASCII character set is generated with
	   jot -c 128 0

     and the strings xaa through xaz with
	   jot -w xa%c 26 a

     while 20 random 8-letter strings are produced with
	   jot -r -c 160 a z | rs -g 0 8

     Infinitely many yes's may be obtained through
	   jot -b yes 0

     and thirty ed(1) substitution commands applying to lines 2, 7, 12, etc. is the result of
	   jot -w %ds/old/new/ 30 2 - 5

     The stuttering sequence 9, 9, 8, 8, 7, etc. can be produced by truncating the output precision and a suitable choice of step size, as in
	   jot -w %d - 9.5 0 -.5

     and a file containing exactly 1024 bytes is created with
	   jot -b x 512 > block

     Finally, to set tabs four spaces apart starting from column 10 and ending in column 132, use
	   expand -`jot -s, - 10 132 4`

     and to print all lines 80 characters or longer,
	   grep `jot -s "" -b . 80`

DIAGNOSTICS

     The following diagnostic messages deserve special explanation:

     illegal or unsupported format '%s'  The requested conversion format specifier for printf(3) was not of the form
	   %[#][ ][{+,-}][0-9]*[.[0-9]*]?
     where ``?'' must be one of
	   [l]{d,i,o,u,x}
     or
	   {c,e,f,g,D,E,G,O,U,X}

     range error in conversion	A value to be printed fell outside the range of the data type associated with the requested output format.

     too many conversions  More than one conversion format specifier has been supplied, but only one is allowed.

SEE ALSO

     ed(1), expand(1), rs(1), seq(1), yes(1), arc4random(3), printf(3), random(3)

HISTORY

     The jot utility first appeared in 4.2BSD.

BSD
								   June 2, 2010 							       BSD