08-17-2010
Can u check out /etc/system file.........
Or try to go to single user mode and check it out.
Last edited by snchaudhari2; 08-17-2010 at 02:30 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
We have a SunFire V880, hooked up with 2 T3 arrays. When ever we issue a reboot command on the system, it hangs at the same place right where it says
syncing file systems done.
To bring it back we shutdown power and it comes clean.
By the way init 6 command works fine.
Has anyone come... (3 Replies)
Discussion started by: smohd
3 Replies
2. Solaris
hello all I have prob with solaris 10 and vmware 5.5, 6.0 that befor it's good work and from yesterday when I try to add new vm in SCSI Controller from vmware it's Don't see any Hard Disk or controller when I used solaris 5 cd-cdrom
and DVD version but when try to make vm with IDE controller... (0 Replies)
Discussion started by: Hosam
0 Replies
3. Solaris
pls can someone direct me on the vmware product that i can install on solaris 10 (4 Replies)
Discussion started by: seyiisq
4 Replies
4. Solaris
Hi,
While we rebooting solaris server ,the system going to Maintenance mode instead of login console.
even we are not able to run fsck command . Thanks in advanced for help.
log attached FYI
Executing last command: boot
Boot device: /pci@83,4000/FJSV,ulsa@2,1/disk@0,0 File and args:... (3 Replies)
Discussion started by: helplineinc
3 Replies
5. Solaris
Hi,
I have set the date on solaris system , but the the date is changed after rebooting the system . I was suspecting that it could sync with ntp server , so i disabled the NTP and checked, but still whenever i reboot the system , the date that i set is getting changed, Any idea how to come out... (7 Replies)
Discussion started by: thavamaniraja
7 Replies
6. Solaris
Hi All,
I had install the solaris 10 into the SUNFIRE V890 server, after installed, it keep rebooting.
I wish to enter the OK mode again, and install back the Solaris 10.
i had try the "break" button and "stop+A" button, but all fail.
kindly advice... (4 Replies)
Discussion started by: SmartAntz
4 Replies
7. Solaris
Hello All,
Solaris 10 which installed in Vmware workstation rebooting automatically and throwing the following error. Looks kernel thread issue, Need experts advice.
Error:
Warning: rpcmod:svc_default_stksize is set more than once in /etc/system/. "set rpcmod:svc_default_stksize =... (0 Replies)
Discussion started by: gowthamakanthan
0 Replies
8. Solaris
Hello Admins,
I am facing an issue with Solaris system running/rebooting on vmware. It has VCS installed and configured. It is a 2nd node out of 3-node cluster.
After long time I opened these 3 nodes to run. Rest 2 nodes are running OK. This 1 node is starting and rebooting itself.
Attached... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. Solaris
Hi all,
How to auto start a snmpd deamon on rebooting a Solaris 5.10 x86 machine.
snmpd's path: /opt/download/net-snmp/sbin
Thank you in advance. (6 Replies)
Discussion started by: ziosnim
6 Replies
10. Solaris
Hi
I need to know the procedure to add the IP to Solaris 11 zone without rebooting the zone..
I did it on solaris 10 zones but don't know the procedure on solaris 11 zones without rebooting it (1 Reply)
Discussion started by: hb00
1 Replies
LEARN ABOUT CENTOS
filecap
FILECAP:(8) System Administration Utilities FILECAP:(8)
NAME
filecap - a program to see capabilities
SYNOPSIS
filecap [ -a | -d | /dir | /dir/file [cap1 cap2 ...] ]
DESCRIPTION
filecap is a program that prints out a report of programs with file based capabilities. If a file is not in the report or there is no
report at all, no capabilities were found. For expedience, the default is to check only the directories in the PATH environmental variable.
If the -a command line option is given, then all directories will be checked. If a directory is passed, it will recursively check that
directory. If a path to a file is given, it will only check that file. If the path to the file includes capabilities, then they are written
to the file.
OPTIONS
-a This tells the program to show all capabilities starting from the / directory. Normally the PATH environmental variable is used to
show you capabilities on files you are likely to execute.
-d This dumps all capabilities for reference.
EXAMPLES
To check file capabilities in $PATH:
filecap
To check file capabilities of whole system:
filecap -a
To check file capabilities recursively in a directory:
filecap /usr
To check file capabilities of a specific program:
filecap /bin/passwd
To list all possible capabilities:
filecap -d
To set a file capability on a specific program:
filecap /bin/ping net_raw net_admin
SEE ALSO
pscap(8), netcap(8), capabilities(7).
AUTHOR
Steve Grubb
Red Hat March 2009 FILECAP:(8)