i haven't tried this, but please check if fstress is helpful for you
How would i make a script for checking the same.
I have created following script but There seems to be some problem with the script.
Whenever i execute it nothing get displayed.What could be the issue.
If a file size increases in Linux/UNIX to say in GB's then will there be a decrease in write speed.
I mean will it take more time to write to a large file then to a small one??
Please clarify?
Thanks in advance (2 Replies)
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Would simply like to write data (no audio) to a CD/RW disk. The disk drive states CD/RW on the front but don't know for sure if the software is configured to recognize it as a writable disk. I can read/move data from the disk to the hard drive with no issue from the disk. Any help in this... (4 Replies)
I am now on Kernel 2.6.32-26
For me 16x CD write speed is okay.
I have old hardware which was able to write DVDs at 1x, back in previous linux version.
Now, I dont get speed of less than 4x.
Tested on k3b, xfburn, and brasero. But all start at bottom 4x write speed. k3b forced back to... (0 Replies)
Hi,
I went to a computer store and the salesman sold me a SATA cable and told me that all SATA cables are the same. Another salesman at a different store told me a cable rated for SATA 2, which I bought, MIGHT work as well as one rate for SATA 3 but it is not guaranteed. I decided to run a... (3 Replies)
hi all:
as we know , when usb flash disk plug in and aotu mounted , the default permission of the usb flash disk is 700. that means others have no permission . the question: how to make others have read/write permission when the aotu mounted usb flash disk pluge in ? thanks !! (0 Replies)
Hi,
We have two servers in scenario (vmsoldot01 is Oracle VM with Linux and tldtppod15 is physical Linux server). One NAS share is mounted on both servers with similar permissions and access. But READ speed is too bad on virtual in comparison to physical server.
While trying to diagnose this, I... (2 Replies)
Hello All,
I am building a real time parser for a log file in my application.
The log file is continuously written at a very fast pace and gets rolled over every 10 minutes.
I have measured the speed and observed that around 1000 lines are written to it every second, each line about 30-40... (7 Replies)
Discussion started by: cool.aquarian
7 Replies
LEARN ABOUT CENTOS
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO chown(1), mknod(1), sd(4), mount(8)COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)