Hi,
We have a SunFire V880, hooked up with 2 T3 arrays. When ever we issue a reboot command on the system, it hangs at the same place right where it says
syncing file systems done.
To bring it back we shutdown power and it comes clean.
By the way init 6 command works fine.
Has anyone come... (3 Replies)
hello all I have prob with solaris 10 and vmware 5.5, 6.0 that befor it's good work and from yesterday when I try to add new vm in SCSI Controller from vmware it's Don't see any Hard Disk or controller when I used solaris 5 cd-cdrom
and DVD version but when try to make vm with IDE controller... (0 Replies)
Hi,
While we rebooting solaris server ,the system going to Maintenance mode instead of login console.
even we are not able to run fsck command . Thanks in advanced for help.
log attached FYI
Executing last command: boot
Boot device: /pci@83,4000/FJSV,ulsa@2,1/disk@0,0 File and args:... (3 Replies)
Hi,
I have set the date on solaris system , but the the date is changed after rebooting the system . I was suspecting that it could sync with ntp server , so i disabled the NTP and checked, but still whenever i reboot the system , the date that i set is getting changed, Any idea how to come out... (7 Replies)
Hi All,
I had install the solaris 10 into the SUNFIRE V890 server, after installed, it keep rebooting.
I wish to enter the OK mode again, and install back the Solaris 10.
i had try the "break" button and "stop+A" button, but all fail.
kindly advice... (4 Replies)
Hello All,
Solaris 10 which installed in Vmware workstation rebooting automatically and throwing the following error. Looks kernel thread issue, Need experts advice.
Error:
Warning: rpcmod:svc_default_stksize is set more than once in /etc/system/. "set rpcmod:svc_default_stksize =... (0 Replies)
Hello Admins,
I am facing an issue with Solaris system running/rebooting on vmware. It has VCS installed and configured. It is a 2nd node out of 3-node cluster.
After long time I opened these 3 nodes to run. Rest 2 nodes are running OK. This 1 node is starting and rebooting itself.
Attached... (4 Replies)
Hi all,
How to auto start a snmpd deamon on rebooting a Solaris 5.10 x86 machine.
snmpd's path: /opt/download/net-snmp/sbin
Thank you in advance. (6 Replies)
Hi
I need to know the procedure to add the IP to Solaris 11 zone without rebooting the zone..
I did it on solaris 10 zones but don't know the procedure on solaris 11 zones without rebooting it (1 Reply)
Discussion started by: hb00
1 Replies
LEARN ABOUT CENTOS
grub-file
GRUB-FILE(1) User Commands GRUB-FILE(1)NAME
grub-file - check file type
SYNOPSIS
file OPTIONS FILE
DESCRIPTION
Check if FILE is of specified type.
--is-i386-xen-pae-domu
Check if FILE can be booted as i386 PAE Xen unprivileged guest kernel
--is-x86_64-xen-domu
Check if FILE can be booted as x86_64 Xen unprivileged guest kernel
--is-x86-xen-dom0
Check if FILE can be used as Xen x86 privileged guest kernel
--is-x86-multiboot
Check if FILE can be used as x86 multiboot kernel
--is-x86-multiboot2 Check if FILE can be used as x86 multiboot2 kernel
--is-arm-linux
Check if FILE is ARM Linux
--is-arm64-linux
Check if FILE is ARM64 Linux
--is-ia64-linux
Check if FILE is IA64 Linux
--is-mips-linux
Check if FILE is MIPS Linux
--is-mipsel-linux
Check if FILE is MIPSEL Linux
--is-sparc64-linux
Check if FILE is SPARC64 Linux
--is-powerpc-linux
Check if FILE is POWERPC Linux
--is-x86-linux
Check if FILE is x86 Linux
--is-x86-linux32
Check if FILE is x86 Linux supporting 32-bit protocol
--is-x86-kfreebsd
Check if FILE is x86 kFreeBSD
--is-i386-kfreebsd
Check if FILE is i386 kFreeBSD
--is-x86_64-kfreebsd
Check if FILE is x86_64 kFreeBSD
--is-x86-knetbsd
Check if FILE is x86 kNetBSD
--is-i386-knetbsd
Check if FILE is i386 kNetBSD
--is-x86_64-knetbsd Check if FILE is x86_64 kNetBSD
--is-i386-efi
Check if FILE is i386 EFI file
--is-x86_64-efi
Check if FILE is x86_64 EFI file
--is-ia64-efi
Check if FILE is IA64 EFI file
--is-arm64-efi
Check if FILE is ARM64 EFI file
--is-arm-efi
Check if FILE is ARM EFI file
--is-hibernated-hiberfil
Check if FILE is hiberfil.sys in hibernated state
--is-x86_64-xnu
Check if FILE is x86_64 XNU (Mac OS X kernel)
--is-i386-xnu
Check if FILE is i386 XNU (Mac OS X kernel)
--is-xnu-hibr
Check if FILE is XNU (Mac OS X kernel) hibernated image
--is-x86-bios-bootsector
Check if FILE is BIOS bootsector
-h, --help Display this help and exit. -u, --usage Display the usage of this command and exit.
SEE ALSO
The full documentation for grub-file is maintained as a Texinfo manual. If the info and grub-file programs are properly installed at your
site, the command
info grub-file
should give you access to the complete manual.
grub-file (GRUB) 2.02-2ubuntu8.3 July 2018 GRUB-FILE(1)