I got something I haven't been able to fix
I configure a Linux Suse 10 box, added static IP, DNS (resolv), gateway (routes) but I am not able to ping other servers by name but nslookup works and the server can navigate on internet
check below
the problematic server is server-host20
other server can ping that server by name just fine
all my network information
by the way my server can ping DNS server by name just ok and as you see nslookup works
Hi.
I just installed the HP-UX 11i V2.
I have problems with CDE - it is inoperative (after logon there is a message box: messaging system failure - or something like that, it asks to check /etc/hosts and network settings).
nslookup works by hostname and IP, hostname shown the correct... (7 Replies)
Hi All,
My current setup is:
1x Windows Server (Windows 2000 server)
1x Unix Server
2x Windows machine
3x Unix Terminals (Hostnames = A, B and C)
Problem
The problem iam having is Unix terminal C cannot be ping across by Unix terminal A or B or Unix server by using the hostname. Unix... (1 Reply)
I recently installed Solaris 10 on my Sun workstation. I cannot ping using hostname from another computer on the same network.
But I can ping using the IP address. Also I can ping other systems using their hostnames.
Can anyone give some information regarding how to resolve this issue. (4 Replies)
Hello everyone
I have a partition with a problem with ping.
If I do a ping by ip for example ping 1.1.1.1 I got no problem but If I ping by hostname for example ping partition1 take almost a minute to respond me.
I have Aix 5.3 and I have another 19 partitions with no problem. The only... (5 Replies)
hi I have Suse Ent 10 SP3 that when I reboot the server sometimes it won't... it behaves like this
up and running If I rebooted boots ok
so up and running again and If I rebooted again it won't from Hadr Drives
What I can check on my boot/grub?
why sometimes boots OK and sometimes does... (0 Replies)
anyone ever seen this problem:
I can ping the server by IP address but I can't by hostname.
nslookup is working and dns query is ok.
# nslookup mwxnsb24
Server: 10.11.49.206
Address: 10.11.49.206#53
Name: mwxnsb24
Address: 10.10.58.175
# ping... (8 Replies)
hi....
i have sun solaris 10 server, fedora 10, and Windows Server.. i cant ping my sun solaris 10, fedora 10 and Windows Server using hostname (etc: ping winserver.bengkel2.com), but i can ping all using IPV4 and IPV6 address.. can u give some suggestion to solve my problem or some idea to... (3 Replies)
Hi
We have some 300 servers in the Data center and some of them are running with AIX and some of them are running with Solaris.
I need a script which can be run in one of the server and that script should ping the hostname of all the 300 servers.
Also the script should notify if any server is... (9 Replies)
I have vmware on my windows PC ( hostname : acer ).
vmware has RHEL 7 ( hostname : rhel7 ) installed recently.
RHEL IP configuration
IP : 192.168.5.128
Netmask : 255.255.255.0
ssh to rhel7 works from acer using putty
resolve.conf
cat /etc/resolv.conf
nameserver 192.168.5.1
host... (12 Replies)
Discussion started by: hiten.r.chauhan
12 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD