Sponsored Content
Operating Systems AIX IBM Server doesn't ping gateway unless you put a static route Post 302444786 by witt on Thursday 12th of August 2010 08:21:42 PM
Old 08-12-2010
IBM Server doesn't ping gateway unless you put a static route

Just want to know if someone has a clue about what could be happening here:

I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.

When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.

Thanks in Advance,
--witt
 

10 More Discussions You Might Find Interesting

1. IP Networking

static route ?

Hi, I have a machine that sits on 10.2 network. I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs what should I need to do? Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies

2. HP-UX

Static route for hpux 11.22

I want to make static route how would I proceed? I'm using "route add DestinationIP gatewayIP hop to 1 I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where? I did a search got this site, it didn't help much. ... (2 Replies)
Discussion started by: catwomen
2 Replies

3. UNIX for Dummies Questions & Answers

Static Route

Hi, Request you to please tell me the command or the process to add the static route in redhat linux. Thanks in Advance. Regards Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies

4. AIX

removing static route

#netstat -nr (shows the following with more static routes) 192.168.18.202 10.129.155.1 UGH 0 29 en0 - - and i just want to remove the above one i tried #smitty rmroute destination type= net dest add = 192.168.18.202 default gateway= 10.129.155.1 net... (1 Reply)
Discussion started by: pchangba1
1 Replies

5. IP Networking

When to use static route on server?

Hi guys, sorry for asking noob question. When do we really need to add a static route on the server? I encounter this situation whereby a client trigger a network packet to the destination but the destination does not know how to return the traffic back to the client (source). The issue was... (4 Replies)
Discussion started by: DrivesMeCrazy
4 Replies

6. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ... (0 Replies)
Discussion started by: mfondoum
0 Replies

7. AIX

Edit Static Route

Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Discussion started by: bbbngowc
3 Replies

8. Red Hat

Static route not added

Hello Guys.. I am facing this weird problem of static route not added after reboot!! Following is my route-<interface> file.. # cat /etc/sysconfig/network-scripts/route-eth0 ADDRESS0=172.31.0.1 NETMASK0=255.255.255.255 GATEWAY0=192.168.208.1 ADDRESS1=172.31.15.2... (3 Replies)
Discussion started by: parth_buch
3 Replies

9. IP Networking

Static route on router

Hi all, This may be the basic question of Routing but I am a sort of new to networking so I am asking. Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes. lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies

10. Red Hat

Can C program put message to IBM MQ remotely, if local server doesn't have MQ library?

Can somebody know if it is possible to connect to remote IBM MQ, if local server using C, but don't have MQ library? Thanks for contribution (0 Replies)
Discussion started by: digioleg54
0 Replies
OCF_PACEMAKER_PING(7)					      Pacemaker Configuration					     OCF_PACEMAKER_PING(7)

NAME
ocf_pacemaker_ping - node connectivity SYNOPSIS
[OCF_RESKEY_pidfile=string] [OCF_RESKEY_dampen=integer] [OCF_RESKEY_name=string] [OCF_RESKEY_multiplier=integer] [OCF_RESKEY_host_list=string] [OCF_RESKEY_attempts=integer] [OCF_RESKEY_timeout=integer] [OCF_RESKEY_options=string] [OCF_RESKEY_debug=string] ping [start | stop | reload | monitor | meta-data | validate-all] DESCRIPTION
Every time the monitor action is run, this resource agent records (in the CIB) the current number of ping nodes the host can connect to. It is essentially the same as pingd except that it uses the system ping tool to obtain the results. SUPPORTED PARAMETERS
OCF_RESKEY_pidfile = string [/var/run//ping-default] PID file OCF_RESKEY_dampen = integer [5s] Dampening interval The time to wait (dampening) further changes occur OCF_RESKEY_name = string [pingd] Attribute name The name of the attributes to set. This is the name to be used in the constraints. OCF_RESKEY_multiplier = integer [] Value multiplier The number by which to multiply the number of connected ping nodes by OCF_RESKEY_host_list = string [] Host list The list of ping nodes to count. Defaults to all configured ping nodes. Rarely needs to be specified. OCF_RESKEY_attempts = integer [2] no. of ping attempts Number of ping attempts, per host, before declaring it dead OCF_RESKEY_timeout = integer [2] ping timeout in seconds How long, in seconds, to wait before declaring a ping lost OCF_RESKEY_options = string [] Extra Options A catch all for any other options that need to be passed to ping. OCF_RESKEY_debug = string [false] Verbose logging Enables to use default attrd_updater verbose logging on every call. AUTHOR
Andrew Beekhof <andrew@beekhof.net> Author. Pacemaker Configuration 07/05/2010 OCF_PACEMAKER_PING(7)
All times are GMT -4. The time now is 05:16 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy