Sponsored Content
Operating Systems SCO Backup MBR an Partition Table Post 302443982 by ccc on Tuesday 10th of August 2010 02:59:04 PM
Old 08-10-2010
Thx, but howto find the device of the whole disk?
Is it a correct way using fdisk?
Code:
scounix# fdisk

        1. Display Partition Table
        2. Use Entire Disk for UNIX
        3. Use Rest of Disk for UNIX
        4. Create UNIX Partition
        5. Activate Partition
        6. Delete Partition
        7. Create Partition

Enter your choice or 'q' to quit: 1

Current Hard Disk Drive: /dev/rhd00

        +-------------+----------+-----------+---------+---------+---------+
        | Partition   | Status   | Type      |   Start |     End |    Size |
        +-------------+----------+-----------+---------+---------+---------+
        | 1           | Active   | UNIX      |       1 | 4444904 | 4444904 |
        +-------------+----------+-----------+---------+---------+---------+

Total disk size: 4445160 tracks (256 reserved for masterboot and diagnostics)

The whole disk seems to be /dev/rhd00.

I'd like to copy MBR to a file.
BTW using:
Code:
dd if=/dev/rhd00 of=/tmp/mbr.bin bs=64k

does it copy partition table as well?

or perhaps this?
Code:
scounix# dd if=/dev/rhd00 of=/tmp/mbr.bin bs=512 count=1
1+0 records in
1+0 records out


Last edited by ccc; 08-10-2010 at 04:09 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

recovery partition table from fdisk?

I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk. The possible reason could be: 1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies

2. UNIX for Advanced & Expert Users

resizing the partition table

Host 1 ------- Part Tag Flag Cylinders Size Blocks 0 root wm 0 - 1911 18.56GB (1912/0/0) 38913024 1 swap wu 1912 - 5434 34.19GB (3523/0/0) 71700096 2 backup wm 0 - 14086 136.71GB ... (5 Replies)
Discussion started by: sriny
5 Replies

3. UNIX for Advanced & Expert Users

modify a predefined partition table on Solaris

I want to modify a predefined partition on Solaris. This predefined partion has 51 GB. I want to partition it as two partition. One is 5G, another one is about 46 GB. I want to use these commands: #format specify disk #partition # modify The system told me that ' Cannot modify disk... (1 Reply)
Discussion started by: duke0001
1 Replies

4. Solaris

Can I put my own tags in a partition table

I have X4500 running Solaris 10. I have formatted a disk and created partition table as given below. Specify disk (enter its number): 0 selecting c0t0d0 /dev/dsk/c0t0d0s0 is part of active ZFS pool zpool1. Please see zpool(1M). FORMAT MENU: disk - select a disk ... (3 Replies)
Discussion started by: bharu_sri
3 Replies

5. Filesystems, Disks and Memory

Creating /boot partition & MBR concerns

I have 40GB HD with mepis8, swap, MBR and under flags word boot. I also have a 160 GB external with a few Linux OS, no swaps, no extended etc. I am total Linux no MS I would feel more secure by resizing that sda1 partition and creating a /boot partition with the MBR housed there. Is that a... (1 Reply)
Discussion started by: worthamtx
1 Replies

6. Slackware

Help me!!!! - Slackware 12 Issue - Invalid Partition table

Hi All, I am a linux newbie. After working with my loveable FEDORA 10 for months, i found it a bit slower. I wanted to try with slackware this time. I already had Windows XP and fedora in my 80 GB SATA disk. Now i allotted 15 GB ( SWAP + / + /home/usr ). During my installation i encountered no... (5 Replies)
Discussion started by: beinthemiddle
5 Replies

7. Solaris

Manually editing partition table

I'm manually editing the partition table purely for experimenting. I did prtvtoc /dev/dsk/c1t0d0s2 > /tmp/prtvtoc I'm trying to split up partition 5 to make partition 6. I'm running into a cylinder boundary error on partition 6. Any clues? # vi /tmp/prtvtoc "/tmp/prtvtoc" 23 lines, 769... (1 Reply)
Discussion started by: adelsin
1 Replies

8. Boot Loaders

GRUB MBR and restoring a partition

I tried to install another Linux O.S along with MS and to make two Linux's and one windows.Usually when I try this GRUB losses the ability to boot the first Linux install. It did it again. I would really like to get this first install bootable again. Here are some facts. -I have a rescue... (0 Replies)
Discussion started by: theKbStockpiler
0 Replies

9. Solaris

System partition backup

Dear All, I am using solaris 9,I want to take the backup all the partition of my system 1 by 1 and put it into tape device. Below is the df -kh output Filesystem size used avail capacity Mounted on /dev/md/dsk/d1 11G 3.4G 7.9G 31% / /dev/md/dsk/d6 ... (4 Replies)
Discussion started by: monojcool
4 Replies

10. Programming

How do I partition an Oracle 11g Table?

Hello, I have a database called "audit_database" and I want to create two tables. Table 1 = Table 1 Table 2 = Audit I want to partition the Audit table into partitions grouped by month. I'm not familiar with table partitioning but doing some reading online shows that it can be done but... (4 Replies)
Discussion started by: bbbngowc
4 Replies
SYSTEMD-GPT-AUTO-GENERATOR(8)				    systemd-gpt-auto-generator				     SYSTEMD-GPT-AUTO-GENERATOR(8)

NAME
systemd-gpt-auto-generator - Generator for automatically discovering and mounting root, /home and /srv partitions, as well as discovering and enabling swap partitions, based on GPT partition type GUIDs. SYNOPSIS
/lib/systemd/system-generators/systemd-gpt-auto-generator DESCRIPTION
systemd-gpt-auto-generator is a unit generator that automatically discovers root, /home, /srv and swap partitions and creates mount and swap units for them, based on the partition type GUIDs of GUID partition tables (GPT). It implements the Discoverable Partitions Specification[1]. Note that this generator has no effect on non-GPT systems, or where the directories under the mount points are already non-empty. Also, on systems where the units are explicitly configured (for example, listed in fstab(5)), the units this generator creates are overridden, but additional implicit dependencies might be created. This generator will only look for root partitions on the same physical disk the EFI System Partition (ESP) is located on. It will only look for the other partitions on the same physical disk the root file system is located on. These partitions will not be searched on systems where the root file system is distributed on multiple disks, for example via btrfs RAID. systemd-gpt-auto-generator is useful for centralizing file system configuration in the partition table and making manual configuration in /etc/fstab or suchlike unnecessary. This generator looks for the partitions based on their partition type GUID. The following partition type GUIDs are identified: Table 1. Partition Type GUIDs +-------------------------------------+--------------------------------+--------------------------------------+ |Partition Type GUID | Name | Explanation | +-------------------------------------+--------------------------------+--------------------------------------+ |44479540-f297-41b2-9af7-d131d5f0458a | Root Partition (x86) | On 32-bit x86 systems, the first x86 | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |4f68bce3-e8cd-4db1-96e7-fbcaf984b709 | Root Partition (x86-64) | On 64-bit x86 systems, the first | | | | x86-64 root partition on the disk | | | | the EFI ESP is located on is mounted | | | | to the root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |69dad710-2ce4-4e3c-b16c-21a1d49abed3 | Root Partition (32-bit ARM) | On 32-bit ARM systems, the first ARM | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |b921b045-1df0-41c3-af44-4c6f280d3fae | Root Partition (64-bit ARM) | On 64-bit ARM systems, the first ARM | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |993d8d3d-f80e-4225-855a-9daf8ed7ea97 | Root Partition (Itanium/IA-64) | On Itanium systems, the first | | | | Itanium root partition on the disk | | | | the EFI ESP is located on is mounted | | | | to the root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |933ac7e1-2eb4-4f13-b844-0e14e2aef915 | Home Partition | The first home partition on the disk | | | | the root partition is located on is | | | | mounted to /home. | +-------------------------------------+--------------------------------+--------------------------------------+ |3b8f8425-20e0-4f3b-907f-1a25a76f98e8 | Server Data Partition | The first server data partition on | | | | the disk the root partition is | | | | located on is mounted to /srv. | +-------------------------------------+--------------------------------+--------------------------------------+ |0657fd6d-a4ab-43c4-84e5-0933c84b4f4f | Swap | All swap partitions located on the | | | | disk the root partition is located | | | | on are enabled. | +-------------------------------------+--------------------------------+--------------------------------------+ |c12a7328-f81f-11d2-ba4b-00a0c93ec93b | EFI System Partition (ESP) | The first ESP located on the disk | | | | the root partition is located on is | | | | mounted to /boot or /efi, see below. | +-------------------------------------+--------------------------------+--------------------------------------+ The /home and /srv partitions may be encrypted in LUKS format. In this case, a device mapper device is set up under the names /dev/mapper/home and /dev/mapper/srv. Note that this might create conflicts if the same partition is listed in /etc/crypttab with a different device mapper device name. Mount and automount units for the EFI System Partition (ESP) are generated on EFI systems. The ESP is mounted to /boot, unless a mount point directory /efi exists, in which case it is mounted there. Since this generator creates an automount unit, the mount will only be activated on-demand, when accessed. On systems where /boot (or /efi if it exists) is an explicitly configured mount (for example, listed in fstab(5)) or where the /boot (or /efi) mount point is non-empty, no mount units are generated. When using this generator in conjunction with btrfs file systems, make sure to set the correct default subvolumes on them, using btrfs subvolume set-default. systemd-gpt-auto-generator implements systemd.generator(7). SEE ALSO
systemd(1), systemd.mount(5), systemd.swap(5), systemd-fstab-generator(8), systemd-cryptsetup@.service(8), cryptsetup(8), fstab(5), btrfs(8) NOTES
1. Discoverable Partitions Specification https://www.freedesktop.org/wiki/Specifications/DiscoverablePartitionsSpec/ systemd 237 SYSTEMD-GPT-AUTO-GENERATOR(8)
All times are GMT -4. The time now is 12:53 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy