08-09-2010
Do you use the automounter at all ?
I setup the same as you had above on a generic Sol 9 box and it worked fine.
Could you also supply an "cat /etc/shells" , "grep agent /etc/group" and "cat /etc/nsswitch.conf".
Thx
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Is there any command which can list me all the Group ID's (Primary, Secondary ) assocaited with a single user.
Thanks
Sanjay (2 Replies)
Discussion started by: sanjay92
2 Replies
2. UNIX for Dummies Questions & Answers
Hi!!,
I am on HP UX -11. I have created a new group and want to assign some the users to this group without changing their existing group ( The new group is the secondary group for them)
Any ideas how to do it??
SAM doesnt seem to be working.. Any way of doing it from command line??
... (1 Reply)
Discussion started by: jyotipg
1 Replies
3. Shell Programming and Scripting
Is there a command or better combination of cmds that will give me the list of Unix users in a particular Unix group whether their primary group is that group in question (information stored in /etc/passwd) or they are in a secondary group (information stored in /etc/group).
So far all I got... (5 Replies)
Discussion started by: ckmehta
5 Replies
4. UNIX for Dummies Questions & Answers
Hi There,
How many user can be added to a unix single group. I need this for unix and solaris.
BRs
-----Post Update-----
I'm asking about secondary group and not primary group. All the users are having 8 character as their username.
value is set for getconf LINE_MAX is... (1 Reply)
Discussion started by: maestromani
1 Replies
5. Solaris
Experts,
I know when I use id it shows only the primary group information for the given user, and that info comes from passwd file. When I use groups it shows all groups user are member of, however from where come information given by groups command?
grep fmtt3990 /etc/passwd... (6 Replies)
Discussion started by: fmattos
6 Replies
6. UNIX for Advanced & Expert Users
We have created ACL's to allow two differnet groups to access some directories. You can see output from getfacl below.
group::rwx
group:rbauser:r--
The original group has full access, the secondary group has read only. However users in the secondary group can't see the directories. Think this... (1 Reply)
Discussion started by: dw82199
1 Replies
7. Red Hat
Hi,
I would like to know how to find our secondary group of user only.
I have used the command id -Gn user1
it is showing both groups of user.
Primary and secondary group. (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Linux
Hello,
i try to add user john to secondary group, named groupB
this will add as primary group,
how can i add to secondary group??
dn: cn=groupB,ou=Groups,dc=ldap-server,dc=com
changetype: modify
add: memberuid
memberuid: john (1 Reply)
Discussion started by: prpkrk
1 Replies
9. UNIX for Dummies Questions & Answers
Oracle Linux 6.6
grid user's secondary groups are asmadmin,asmdba,asmoper and dba
# id -a grid
uid=638(grid) gid=2000(oinstall) groups=2000(oinstall),2100(asmadmin),2200(dba),2300(asmdba),2301(asmoper)
I want to remove dba as the secondary group for grid and keep the remaining ones.
ie. I... (5 Replies)
Discussion started by: John K
5 Replies
10. Windows & DOS: Issues & Discussions
Hi ,
Is there a way to find out when an account was added to a group in Windows 2003?Could you please tell me how to find that?
Regards,
Maddy (1 Reply)
Discussion started by: Maddy123
1 Replies
LEARN ABOUT SUSE
unbuffer
UNBUFFER(1) General Commands Manual UNBUFFER(1)
NAME
unbuffer - unbuffer output
SYNOPSIS
unbuffer program [ args ]
INTRODUCTION
unbuffer disables the output buffering that occurs when program output is redirected from non-interactive programs. For example, suppose
you are watching the output from a fifo by running it through od and then more.
od -c /tmp/fifo | more
You will not see anything until a full page of output has been produced.
You can disable this automatic buffering as follows:
unbuffer od -c /tmp/fifo | more
Normally, unbuffer does not read from stdin. This simplifies use of unbuffer in some situations. To use unbuffer in a pipeline, use the
-p flag. Example:
process1 | unbuffer -p process2 | process3
CAVEATS
unbuffer -p may appear to work incorrectly if a process feeding input to unbuffer exits. Consider:
process1 | unbuffer -p process2 | process3
If process1 exits, process2 may not yet have finished. It is impossible for unbuffer to know long to wait for process2 and process2 may
not ever finish, for example, if it is a filter. For expediency, unbuffer simply exits when it encounters an EOF from either its input or
process2.
In order to have a version of unbuffer that worked in all situations, an oracle would be necessary. If you want an application-specific
solution, workarounds or hand-coded Expect may be more suitable. For example, the following example shows how to allow grep to finish pro-
cessing when the cat before it finishes first. Using cat to feed grep would never require unbuffer in real life. It is merely a place-
holder for some imaginary process that may or may not finish. Similarly, the final cat at the end of the pipeline is also a placeholder
for another process.
$ cat /tmp/abcdef.log | grep abc | cat
abcdef
xxxabc defxxx
$ cat /tmp/abcdef.log | unbuffer grep abc | cat
$ (cat /tmp/abcdef.log ; sleep 1) | unbuffer grep abc | cat
abcdef
xxxabc defxxx
$
BUGS
The man page is longer than the program.
SEE ALSO
"Exploring Expect: A Tcl-Based Toolkit for Automating Interactive Programs" by Don Libes, O'Reilly and Associates, January 1995.
AUTHOR
Don Libes, National Institute of Standards and Technology
1 June 1994 UNBUFFER(1)