Sponsored Content
Operating Systems SCO Migrate SCO 5.0.6 to different hardware Post 302443344 by jgt on Sunday 8th of August 2010 11:22:24 AM
Old 08-08-2010
Go to the SCO web site, and look at the supported hardware list.

SCO |

If what you have is not in the list, you will have to contact the component manufacturer to see if they provide a device driver.
Also, just because an item is in the list, does not mean the the driver is on the original OS CD.

---------- Post updated at 11:22 AM ---------- Previous update was at 11:17 AM ----------

Quote:
Thx, I will try, but do I need an IDE hard disk in the new hardware?
No, but the new system would boot immediately, and without the need for a target kernel, if you were to use an IDE drive as the boot drive, and then add SCSI (RAID ?) for the application and data.
I have not tested using a SATA drive in compatible mode with 5.0.6
This User Gave Thanks to jgt For This Post:
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to migrate ?

Currently, I am planning a migration between machine which under True64UNIX. The new machine will run with higher version O/S. My question is, is there any solution on migrating one machine to another which with different O/S version? My goal is keeping minimum impact to the users. Excuse my... (1 Reply)
Discussion started by: coolmans
1 Replies

2. Solaris

Migrate oracle solaris 5.8 5.9

If I have an oracle 9 database environment on a san running solaris 5.8 as the os. Can I plug the san into a Solaris 5.9 environment and have the database work ? - as long as binaries are on the san (1 Reply)
Discussion started by: tim-carroll@com
1 Replies

3. Linux

Mysql Migrate

Hi , I would like to (MYSQL) migrate the all the data from solari's to linux box. I have checked whether mysql is installed or not. rpm -qa | grep -i mysql I confirmed !!!! I want to know the following points. 1) How can get to know what are mysql data files and location as well.... (4 Replies)
Discussion started by: Mani_apr08
4 Replies

4. Solaris

Hardware faulty, but which hardware?

Hi folk, I have this hardware faunty message, but dont know which hardware is this ? can you guide me ? --------------- ------------------------------------ -------------- --------- TIME EVENT-ID MSG-ID SEVERITY ---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies

5. SCO

Migrate UNIXWare from old machine to new machine (different hardware)

Good afternoon all, I'm a bit stuck... I honestly don't know very much about Unix let alone UnixWare for that matter. I have a system that's very old and could fail really at any time. I have another server I'd like to move everything to yet I don't know what's possible. The current server is... (2 Replies)
Discussion started by: rubiks015
2 Replies

6. SCO

SCO 5.0.7v VM Hardware

I run SCO 5.0.7v in ESXi 5.5 and am looking at ways to increase performance. I notice that the VM hardware is still set to 4 and wondered if there was an advantage in raising it or will this cause issues? (0 Replies)
Discussion started by: stewartg
0 Replies

7. SCO

Recommendation for hardware to run SCO OSR 5.0.7 natively

Looking for a modern server to run SCO OSR 5.0.7 without VM (native), h/w must have manufacturers warranty. Requirements would be to accommodate light loads of up to 15 users, app does not take more than 30 - 40 MB of RAM and data stored takes up to 15 - 20 GB, no internet connections... (3 Replies)
Discussion started by: migurus
3 Replies

8. Linux

How to migrate a running lvm.?

Hi all, Please explain how do i. Migrate and backup a running lvm..!! Thanks, Sent from my LG-D802 using Tapatalk (3 Replies)
Discussion started by: lordkizzo
3 Replies

9. AIX

Migrate AIX to new Hardware

Hello Friends/AIXgurus, When you have time, could you please look into below. We're planning to migrate AIX LPARs on to new Hardware. Requirement: Migrate AIX LPARs from POWER 6 to POWER 8 Hardware (*everything should run as is after the transition) Below is our thought process. Ours... (5 Replies)
Discussion started by: System Admin 77
5 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 05:04 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy