07-29-2010
How to find Ethernet address
Dear Sir,
Thank you very much for ur reply.
I have a doubt as below :
In the command , lsattr -E -l inet0 I guess inet0 stands for Ethernet
How to know , which ethernet is our system using.
Is inet0 , a default for any production server ( I mean the server on which the applications are running) or can there be something like inet1 or inet2 etc
In that case how to find the ethernet address.
Regards,
Pranav
8 More Discussions You Might Find Interesting
1. AIX
Hi,
We are running AIX 5.2.
Our default gateway used to be IP Address A.
Our new default gateway is IP Address B.
A netstat revealed that our default route was IP address A.
We manually added default route with IP address B and removed the default route with IP address A.
However,... (3 Replies)
Discussion started by: DenD
3 Replies
2. AIX
Hi,
After accidental default route removal serial connection doesn't work.
What should I do to connect to my machine ?
thanks
Vilius (7 Replies)
Discussion started by: vilius
7 Replies
3. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
4. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
5. IP Networking
Greetings,
I am using debian squeeze to perform the following operation:
1. pxeboot Alix 2.c board into debian installer
When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this.
I... (2 Replies)
Discussion started by: mock
2 Replies
6. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
7. Solaris
Hi All
Recently we have faced issue in SUN server
after reboot of node 2 default routs has been added to system as below
IRE Table: IPv4
**Destination*************Mask***********Gateway**********Device Mxfrg Rtt***Ref Flg**Out**In/Fwd*
-------------------- ---------------... (2 Replies)
Discussion started by: aaysa123
2 Replies
8. Red Hat
Hi all,
actually i'm facing this problem,
we have 2 NICs on our VM.s with REDHAT 7.2 release,
we made the following set up as we needed to access them from both IP
ip route flush all
ip route add 10.130.11.0/24 dev eno2 tab 1
ip route add 10.130.10.0/24 dev eno1 tab 2
ip route add... (0 Replies)
Discussion started by: charli1
0 Replies
LEARN ABOUT NETBSD
route.conf
ROUTE.CONF(5) BSD File Formats Manual ROUTE.CONF(5)
NAME
route.conf -- static routes config file
DESCRIPTION
The route.conf file is read by the staticroute rc.d script during system start-up and shutdown, and is intended for adding and removing
static routes.
FILE FORMAT
Lines starting with a hash ('#') are comments and ignored. Lines starting with a plus sign ('+') are run during start-up, while lines start-
ing with a minus sign ('-') are run during system shutdown. If a line starts with a '!', the rest of the line will get evaluated as a shell
script fragment. All other lines are passed to route(8). During start-up, they are passed behind a ``route add -'' command and during shut-
down behind a ``route delete -'' command.
FILES
/etc/route.conf The route.conf file resides in /etc.
/etc/rc.d/staticroute
rc.d(8) script that parses route.conf.
EXAMPLES
In this example, the interface for the desired routing changes is set, the IP address on that interface is determined, and a route is added
during startup, or deleted during system shutdown.
# Set interface and determine current IP address for added route.
!ifname=bnx0
!ipaddr=$(/sbin/ifconfig ${ifname} | awk '$1 == "inet" {print $2}')
net 10.10.1 -interface ${ipaddr}
In this example, IP forwarding is turned on during start-up, and a static route added for 192.168.2.0. During system shutdown, the route is
removed and IP forwarding turned off.
# Turn on/off IP forwarding.
+sysctl -w net.inet.ip.forwarding=1
-sysctl -w net.inet.ip.forwarding=0
net 192.168.2.0 -netmask 255.255.255.0 192.168.150.2
SEE ALSO
rc.conf(5), rc(8), route(8)
BSD
May 1, 2012 BSD