07-26-2010
partially what I needed
Ok have the send/recv working, and going to use zpool destroy oldpool, zpool export newpool, zpool import newpool oldpool. My issue now is to make sure all the settings and attributes migrate. So how do I first gather them on oldpool and then set them on newpool.
10 More Discussions You Might Find Interesting
1. Solaris
Hi all
I plan to install Solaris 10U6 on some SPARC server using ZFS as root pool, whereas I would like to keep the current setup done by VxVM:
- 2 internal disks: c0t0d0 and c0t1d0
- bootable root-volume (mirrored, both disks)
- 1 non-mirrored swap slice
- 1 non-mirrored slices for Live... (1 Reply)
Discussion started by: blicki
1 Replies
2. Solaris
# zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: Sun Message ID: ZFS-8000-3C
config:
emcpool1 ... (7 Replies)
Discussion started by: fugitive
7 Replies
3. Infrastructure Monitoring
Here are the details.
cnjr-opennms>root$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
openpool 20.6G 46.3G 35.5K /openpool
openpool/ROOT 15.4G 46.3G 18K legacy
openpool/ROOT/rds 15.4G 46.3G 15.3G /
openpool/ROOT/rds/var 102M ... (3 Replies)
Discussion started by: pupp
3 Replies
4. Solaris
I created a pool the other day. I created a 10 gig files just for a test, then deleted it.
I proceeded to create a few files systems. But for some reason the pool shows 10% full, but the files systems are both at 1%? Both files systems share the same pool.
When I ls -al the pool I just... (6 Replies)
Discussion started by: mrlayance
6 Replies
5. Solaris
Hi guys,
We had created a pool as follows:
zpool create filing_pool raidz c1t2d0 c1t3d0 ........
Due to some requirement, we need to destroy the pool and re-create another one. We wish to know now which disks have been included in the filing_pool, how do we list the disks used to create... (2 Replies)
Discussion started by: frum
2 Replies
6. Solaris
Other than export/import, is there a cleaner way to rename a pool without unmounting de FS?
Something like, say "zpool rename a b"?
Thanks. (2 Replies)
Discussion started by: verdepollo
2 Replies
7. Solaris
installed Solaris 11 Express on my server machine a while ago. I created a Z2 RAID over five HDDs and created a few ZFS filesystems on it.
Once I (unintentionally) managed to fill the pool completely with data and (to my surprise) the filesystems stopped working - I could not read/delete any... (3 Replies)
Discussion started by: RychnD
3 Replies
8. Solaris
I messed up my pool by doing zfs send...recive So I got the following :
zpool list
NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT
rpool 928G 17.3G 911G 1% 1.00x ONLINE -
tank1 928G 35.8G 892G 3% 1.00x ONLINE -
So I have "tank1" pool.
zfs get all... (8 Replies)
Discussion started by: eladgrs
8 Replies
9. Solaris
I accidently added a disk in different zpool instead of pool, where I want.
root@prtdrd21:/# zpool status cvfdb2_app_pool
pool: cvfdb2_app_pool
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
cvfdb2_app_pool ONLINE 0 0 0... (1 Reply)
Discussion started by: solaris_1977
1 Replies
10. Solaris
I have a newly created zpool, and I have set compression on, for the whole pool:
# zfs set compression=on newPool
Now I have zfs send | zfs receive lot of snapshots to my newPool, but the compression is gone. I was hoping that I would be able to send snapshots to the new pool (which is... (0 Replies)
Discussion started by: kebabbert
0 Replies
LEARN ABOUT FREEBSD
zfsboot
ZFSBOOT(8) BSD System Manager's Manual ZFSBOOT(8)
NAME
zfsboot -- bootcode for ZFS on BIOS-based computers
DESCRIPTION
zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool. zfsboot is installed in two parts on a disk or a partition
used by a ZFS pool. The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition. The second
part, a main boot block, is installed at a special offset within the disk or partition. Both areas are reserved by the ZFS on-disk specifi-
cation for boot use. If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
boot blocks described in boot(8).
BOOTING
The zfsboot boot process is very similar to that of gptzfsboot(8). One significant difference is that zfsboot does not currently support the
GPT partitioning scheme. Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels. See
the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.
USAGE
zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).
FILES
/boot/zfsboot boot code binary
/boot.config parameters for the boot block (optional)
/boot/config alternative parameters for the boot block (optional)
EXAMPLES
zfsboot is typically installed using dd(1). To install zfsboot on the ada0 drive:
dd if=/boot/zfsboot of=/dev/ada0 count=1
dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024
If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:
sysctl kern.geom.debugflags=0x10
zfsboot can also be installed in an MBR slice:
gpart create -s mbr ada0
gpart add -t freebsd ada0
gpart create -s BSD ada0s1
gpart bootcode -b /boot/boot0 ada0
gpart set -a active -i 1 ada0
dd if=/boot/zfsboot of=/dev/ada0s1 count=1
dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024
Note that commands to create and populate a pool are not shown in the example above.
SEE ALSO
dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)
HISTORY
zfsboot appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Andriy Gapon <avg@FreeBSD.org>.
BUGS
Installing zfsboot with dd(1) is a hack. ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.
BSD
September 15, 2014 BSD