I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network Config Manager but has the same error.
I've tried updating with MP5 with latest drivers but does not seem to work. I've also used the "# pkgadd -d diskette1" command but it fails half way through for some unknown reason.
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT SUNOS
create-resource-adapter-config
asadmin-create-resource-adapter-config(1AS) User Commands asadmin-create-resource-adapter-config(1AS)NAME
asadmin-create-resource-adapter-config, create-resource-adapter-config - creates the configuration information in
domain.xml for the connector module
SYNOPSIS
create-resource-adapter-config --user admin_user [--password admin_password] [--host localhost] [--port 4848] [--secure|-s] [--passwordfile
filename] [--terse=false] [--echo=false] [--interactive=true] [--threadpools threadpoolids] [--property name=value[:name=value]*] raname
Creates configuration information for the connector module. This command can be executed prior to deploying a resource adapter, so that the
configuration information is available at the time of deployment, or after deployment. If the resource adapter is created after deployment,
the resource adapter is started. You must first create a threadpool, using the create-threadpool command, and then identify that threadpool
value as the ID in the--threadpools option.
This command is supported in remote mode only.
OPTIONS --user authorized domain application server administrative username.
--password password to administer the domain application server.
--host machine name where the domain application server is running.
--port port number of the domain application server listening for administration requests.
--secure if true, uses SSL/TLS to communicate with the domain application server.
--passwordfile file containing the domain application server password.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
--interactive if set to true (default), only the required password options are prompted.
--threadpool the threadpool ID from which the work manager gets the thread.
--property configuration properties of the resource adapter java bean.
OPERANDS
raname the value kept in the resource-adapter-name in the domain.xml file.
Example 1: Using create-resource-adapter-config
asadmin> create-resource-adapter-config --username admin1 --password adminadmin
myresourceadapter
Command create-resource-adapter-config executed successfully
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-threadpool(1AS), asadmin-delete-resource-adapter-config(1AS), asadmin-list-resource-adapter-configs(1AS)J2EE 1.4 SDK March 2004 asadmin-create-resource-adapter-config(1AS)