hey guys
having some trouble figuring this out.
my program is supposed to take a name of a directory as a command line argument and change the filenames inside that directory to lowercase.
what i dont get is how you access that directory and go thru all the files and change the filenames... (1 Reply)
i have many files with extention filename.ASN_ERROR~ at a path. I want to move these files to another path and change extension to .ASN
There are more then 80,000 files so i cant use manual commands
muneebr (5 Replies)
I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Dear All,
I have some thousands of files in a folder and i need to change those file names without opening the file (no need to change anything in the file content, need to change the file name only). The filenames are as follows:
Myfile_name.1_parameter
Myfile_name.2_parameter... (6 Replies)
I have lot of files whose names are something like the following. I want to change the name of all the files from 'npt02' to 'n02'.
npt02-z30-sr65-rgdt0p50-dc0p01-16x12drw.tpf
npt02-z30-sr65-rgdt0p50-dc0p01-8x6drw.back
npt02-z30-sr65-rgdt0p50-dc0p01-8x6drw-bst-mis.xy... (5 Replies)
Hi guys,
I have lots of files that look like:
ABC.packed.dir
DEF.packed.dir
GHI.packed.dir
etc...
I would like them to have more of the usual naming convention
ABC
DEF
GHI
etc...
so I was thinking that I could: (2 Replies)
I have file names as shown and want to change the name to have only the first four numbers.
/home/chrisd/Desktop/nips/nips_2013/5212-learning-feature-selection-dependencies-in-multi-task-learning.pdf
/home/chrisd/Desktop/nips/nips_2013/5213-parametric-task-learning.pdf... (3 Replies)
I have a series of files as follows
file-1.pdf
file-2.pdf
file-3.pdf
file-4.pdf
file-5.pdf
file-6.pdf
file-7.pdf
I want to have the file names with odd numbers
starting from an initial number, for example 2000.
The result would be the following:
file-2001.pdf
file-2003.pdf... (9 Replies)
NTPD.CONF(5) File Formats Manual NTPD.CONF(5)NAME
ntpd.conf - Network Time Protocol daemon configuration file
DESCRIPTION
This manual page describes the format of the ntpd(8) configuration file.
The optional weight keyword permits finer control over the relative importance of time sources (servers or sensor devices). Weights are
specified in the range 1 to 10; if no weight is given, the default is 1. A server with a weight of 5, for example, will have five times
more influence on time offset calculation than a server with a weight of 1.
ntpd.conf has the following format:
Empty lines and lines beginning with the `#' character are ignored.
Keywords may be specified multiple times within the configuration file. They are as follows:
listen on address
OpenNTPd has the ability to sync the local clock to remote NTP servers and, if this directive is specified, can act as NTP server
itself, redistributing the local clock.
Specify a local IP address or a hostname the ntpd(8) daemon should listen on to enable remote clients synchronization. If it
appears multiple times, ntpd(8) will listen on each given address. If `*' is given as an address, ntpd(8) will listen on all local
addresses. ntpd(8) does not listen on any address by default. For example:
listen on *
or
listen on 127.0.0.1
listen on ::1
sensor device [correction microseconds] [weight weight-value]
Specify a timedelta sensor device ntpd(8) should use. The sensor can be specified multiple times: ntpd(8) will use each given sen-
sor that actually exists. Non-existent sensors are ignored. If `*' is given as device name, ntpd(8) will use all timedelta sensors
it finds. ntpd(8) does not use any timedelta sensor by default. For example:
sensor *
sensor udcf0
An optional correction in microseconds can be given to compensate for the sensor's offset. The maximum correction is 127 seconds.
For example, if a DCF77 receiver is lagging 15ms behind actual time:
sensor udcf0 correction 15000
server address [weight weight-value]
Specify the IP address or the hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will try to syn-
chronize to all of the servers specified. If a hostname resolves to multiple IPv4 and/or IPv6 addresses, ntpd(8) uses the first
address. If it does not get a reply, ntpd(8) retries with the next address and continues to do so until a working address is found.
For example:
server 10.0.0.2 weight 5
server ntp.example.org weight 1
To provide redundancy, it is good practice to configure multiple servers. In general, best accuracy is obtained by using servers
that have a low network latency.
servers address [weight weight-value]
As with server, specify the IP address or hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will
try to synchronize to all of the servers specified. Should the hostname resolve to multiple IP addresses, ntpd(8) will try to syn-
chronize to all of them. For example:
servers pool.ntp.org
FILES
/etc/openntpd/ntpd.conf
default ntpd(8) configuration file
SEE ALSO ntpd(8), sysctl(8)HISTORY
The ntpd.conf file format first appeared in OpenBSD 3.6 .
$Mdocdate: October 2 2007 $ NTPD.CONF(5)