07-22-2010
9 More Discussions You Might Find Interesting
1. AIX
I am trying to create a SEA on a LHEA port and it gives me error
lsdev -Cc adapter:
ent0 logical host ethernet port (l-hea)
ent1 virtual I/O ethernet adapter
mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199
method error (/usr/lib/methods/cfgsea):
Failed to configure SEA... (0 Replies)
Discussion started by: filosophizer
0 Replies
2. AIX
Hi all,
I set up the following configuration on my system:
- An LPar with a virtual adapter, first one with a vlan id=703 and id port=13.
- The first adapter have to connect to a VIOS in which i configured an SEA.
So, the VA is set up on interface ent2, SEA on ent29 (by linking a... (0 Replies)
Discussion started by: idro
0 Replies
3. AIX
Hi experts, i got a 4-port Adapter card on VIOS and would like to configure 4SEA for 4 difference segment IP client's LPAR use, first SEA succeed to be configured on ent0 but once second SEA configured, first SEA fail to be connected. Any issues i need to be concerned in order to configure 4 SEA on... (8 Replies)
Discussion started by: polar
8 Replies
4. AIX
I am trying to install a VIOS pair with a load-sharing SEA adapter, following this recipe from Developerworks. Without load-sharing everything went fine and worked as expected, but somehow i am a bit lost and the first tries with "ha_mode=sharing" didn't work at all.
Here is the situation:
I... (6 Replies)
Discussion started by: bakunin
6 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
i want configure a SEA over my vios ,
i have a message error :
Method error (/usr/lib/methods/cfgsea):
Failed to configure SEA with return code 1 and SEA-specific error code 10:
Detailed info: Setting real adapter ent1 in promiscuous mode failed... (5 Replies)
Discussion started by: hedou
5 Replies
7. AIX
hi guys
BTW pretty new to VIO
I inherited 2 I BM Power Server - blades PS701 - One is already configured using en8
# lsdev -Cc adapter | grep ent
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available 04-20... (8 Replies)
Discussion started by: karlochacon
8 Replies
8. AIX
hello,
what will happen if i try to move sea of my 1 vio server to standby( using chdev command), when sea of other vio server is already in standby mode? (1 Reply)
Discussion started by: amvineeth
1 Replies
9. AIX
Hello,
I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time.
Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
LEARN ABOUT DEBIAN
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)
NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS
-raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO
ppm(5)
AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)