07-21-2010
What is a fake network device?
Thanks in advance!
Ben
8 More Discussions You Might Find Interesting
1. Programming
HI,
I am writing a network device driver for RTL8139c card on 2.6.18 kernel ... I am facing few queries listed below
1. Can i able to at all write a driver for RTL8139C or Realtek had designed new chip for 2.6 series kernel?
2. If no then which driver file 2.6.18 uses .. Is it 8139too.c or... (1 Reply)
Discussion started by: niketan
1 Replies
2. UNIX for Dummies Questions & Answers
Good morning!
Why would having a fake network device be useful?
Thanks in advance
Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies
3. Red Hat
How to monitor network device traffic using MRTG?
How can I add network devices in MRTG configuration to monitor? (2 Replies)
Discussion started by: manalisharmabe
2 Replies
4. IP Networking
Hey foks
my problem looks like this:
Computer 1 has two network interfaces (A and B). It's connected to computer 2 via ssh using network interface A. kann I forward network interface B to computer 2, so it shows up for example in ifconfig on computer 2? how? should i use something else than... (1 Reply)
Discussion started by: smf15
1 Replies
5. Shell Programming and Scripting
HI all, im new to shell scripting. need your guidence for my script. i wrote one script and is attached here
Im explaining the requirement of script.
AIM: Shell script to run automatically as per scheduled and backup few network devices configurations. Script will contain a set of commands... (4 Replies)
Discussion started by: saichand1985
4 Replies
6. Shell Programming and Scripting
Hello all,
Here is the explanation of my problem:
I have a cronjob that connects to a NAS to do backups from my laptop to this NAS device.
The script that I wrote does check if there is a host (the NAS) responding on 192.168.1.10 and tries to connect to it with the following command:
mount -v... (3 Replies)
Discussion started by: freddie50
3 Replies
7. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
8. HP-UX
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
PLADV(3plplot) PLplot API PLADV(3plplot)
NAME
pladv - Advance the (sub-)page
SYNOPSIS
pladv(sub)
DESCRIPTION
Advances to the next subpage if sub=0, performing a page advance if there are no remaining subpages on the current page. If subpages
aren't being used, pladv(3plplot)(0) will always advance the page. If sub>0, PLplot switches to the specified subpage. Note that this
allows you to overwrite a plot on the specified subpage; if this is not what you intended, use pleop(3plplot) followed by plbop(3plplot) to
first advance the page. This routine is called automatically (with sub=0) by plenv(3plplot), but if plenv(3plplot) is not used,
pladv(3plplot) must be called after initializing PLplot but before defining the viewport.
Redacted form: pladv(sub)
This function is used in examples 1,2,4,6-12,14-18,20,21,23-27,29,31.
ARGUMENTS
sub (PLINT, input)
Specifies the subpage number (starting from 1 in the top left corner and increasing along the rows) to which to advance. Set to
zero to advance to the next subpage.
AUTHORS
Geoffrey Furnish and Maurice LeBrun wrote and maintain PLplot. This man page was automatically generated from the DocBook source of the
PLplot documentation, maintained by Alan W. Irwin and Rafael Laboissiere.
SEE ALSO
PLplot documentation at http://plplot.sourceforge.net/resources.
August, 2012 PLADV(3plplot)