Sponsored Content
Special Forums Hardware Connect SATA Laptop HardDrive to Desktop SATA Slots Post 302438501 by Zykl0n-B on Tuesday 20th of July 2010 02:11:27 AM
Old 07-20-2010
Hello fpmurphy and thanks for your quick reply.

I took the risk and connected the 2.5' laptop hard drive to the PC SATA connectors, and it worked perfectly, in fact, i'm writing this lines from the operating system i just installed in the 2.5' hard drive. =)

Thanks.
Zykl0n-B
 

9 More Discussions You Might Find Interesting

1. Solaris

SATA driver for soalris 9

can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it. thanks and regards msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies

2. UNIX for Advanced & Expert Users

sata support

i have a system which has two hard disks..one is sata and the other one is normal ata hard disk. i wish to install red hat enterprise linux WS(desktop edition) on my sata hard disk..but the installer shows me only my ata hard disk.. i searched the net..it says that a library-- libata will let it... (2 Replies)
Discussion started by: ankit.jss
2 Replies

3. UNIX for Advanced & Expert Users

Linux o.s on two sata's.

Hi, I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system. When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies

4. UNIX for Advanced & Expert Users

trying to setup a sata drive using a sata to scsi adaptor

trying to setup a sata drive using a sata to scsi adaptor I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies

5. Red Hat

sata/sas controller on redhat

Hi All, How do I verify the sata/sas controller status on my redhat 2.6? Thanks. Itik (1 Reply)
Discussion started by: itik
1 Replies

6. Hardware

SATA drive FAT recover

I had ACER aspiron one netbook with dual bootable (Windows XP and Debian). Recently I found XP is messy and Debian has new version published. I plan to recover XP and install new version of Debian. But I failed to recover XP from Hidden Partition. I thought it is because I install GRUB in the... (15 Replies)
Discussion started by: sinnud
15 Replies

7. Hardware

SPARC, SCSI -> SATA?

I'm thinking about suggesting my boss to go for sata adapter and SSD, instead of buying new SCSI drives for SPARC. out here, a brand new 70Gb SCSI drive is about 100euros, and 140Gb is 200eur! (for that price, one could probably buy the adapter.) has anyone tried it? how well do modern... (1 Reply)
Discussion started by: orange47
1 Replies

8. Hardware

Question on SATA 300 vs SATA 600

I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies

9. Solaris

Sata 2 port not working

I have installed Solaris 11 Express on my machine. On my GA-X58A-UD5 motherboard there are two 6 Gb/s SATA ports (Marvell 9128 chip), but when I connect a hard drive to one of them, the system does not recognize it. However, when I boot from a USB install image (downloaded from here Oracle... (1 Reply)
Discussion started by: RychnD
1 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 02:27 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy