I wanted to print numbers from 1 to 5 in reverse order. For this I used the following code:
Well but on compiling the above code, it gives the following error.
Can anyone please help me out in this regards?
Unable to execute commands using rsh in Solaris 9 and 10.
When I execute this command " rsh -n 172.16.67.91 ls -l " I am getting this error message.
::ffff:172.16.67.91: Connection refused
Please guide me how to enable rsh.
Thanks & Regards
Durgaprasad (1 Reply)
I have a script A which calls script B. I wrote a function in script A to be executed when Kill command is issued for script A and I invoke that function using the trap command.The function identifies all child process running under script A (in this case script B) and kills the child process and... (3 Replies)
Hello,
On Aix 5.3, during importvg, the varyonvg fails:
importvg -y vgtest hdisk20
0516-013 varyonvg: The volume group cannot be varied on because
there are no good copies of the descriptor area.
When i use manually the command varyonvg -u -b -t vgtest to force, the vg can... (3 Replies)
Hi,
I'm unable to execute the below command completely ; it's not allowing me to type the complete command. It is allowing till "xargs" and i cannot even press enter after that.
I'm using Solaris. Let me know if anything needs to be added so as to execute the complete command. Appreciate... (12 Replies)
Hi,
I am very new to this environment - I hope this is the right platform to discuss my issue:
I created a CRON job to run a Stored Procedure from our database - Sybase.
Within the Stored Procedure there is a TRUNCATE table and CREATE table function.
the CRON job fails to run with... (2 Replies)
Hi Friends,
I am not able to execute snap -a command in AIX 6 system. Could you please let me know how to make work this command and Path to be set.
Thanks in Advance
Siva. (4 Replies)
Hi
I am writing a script to get the CPU and memory utilization periodically from glance command.
Wrote a script which consists of below two lines
Script name : Utilization.sh
#!/bin/sh
glance -iterations 1 | sed -n '/Util/p/'| awk '!/Disk/'| awk '!/Swap/' >> file.txt
I am able to run the... (5 Replies)
Discussion started by: Shravani
5 Replies
LEARN ABOUT DEBIAN
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)