ifplugd(8)                                                    System Manager's Manual                                                   ifplugd(8)

NAME

       ifplugd - A link detection daemon for ethernet devices

SYNOPSIS

       ifplugd [options]

DESCRIPTION

       ifplugd  is a daemon which will automatically configure your ethernet device when a cable is plugged in and automatically unconfigure it if
       the cable is pulled. This is useful on laptops with on-board network adapters, since it will only configure the interface when a  cable  is
       really connected.

       It  uses  your  distribution's  native  ifup/ifdown programs, but can be configured to do anything you wish when the state of the interface
       changes. It may ignore short unplugged whiles (-d option) or plugged whiles (-u option).

       ifplugd may be used in "compatibility mode" by specifying -F on the command line. Than ifplugd will treat network drivers which do not sup-
       port link beat querying as always online.

OPTIONS

       -a | --no-auto
              Do not enable interface automatically (default: off)

       -n | --no-daemon
              Do not daemonize (for debugging) (default: off)

       -s | --no-syslog
              Do not use syslog, use stdout instead (for debugging) (default: off).

       -b | --no-beep
              Do not beep (off), overrides --no-beep-up and --no-beep-down.

       -U | --no-beep-up
              Do not beep on interface up (off)

       -D | --no-beep-down
              Do not beep on interface down (off)

       -f | --ignore-fail
              Ignore detection failure, retry instead. Failure is treated as "no link". (default: off)

       -F | --ignore-fail-positive
              Ignore detection failure, retry instead. Failure is treated as "link detected". (default: off)

       -i | --iface= IFACE
              Specify ethernet interface (default: eth0)

       -r | --run= EXEC
              Specify program to execute when link status changes (default: /etc/ifplugd/ifplugd.action)

       -I | --ignore-retval
              Don't exit on nonzero return value of program executed on link change. (default: off)

       -t | --poll-time= SECS
              Specify poll time in seconds (default: 1)

       -T | --poll-utime= USECS
              Specify poll time in microseconds, added to -t (default: 0)

       -u | --delay-up= SECS
              Specify delay for configuring interface (default: 0)

       -d | --delay-down= SECS
              Specify delay for deconfiguring interface (default: 5)

       -m | --api-mode= MODE
              Force  a  specific link beat detection ioctl() API. Possible values are auto, iff, wlan, ethtool, mii, and priv for automatic detec-
              tion, interface flag (IFF_RUNNING), wireless extension, SIOCETHTOOL, SIOCGMIIREG resp. SIOCPRIV. Only the  first  character  of  the
              argument is relevant, case insensitive. (default: auto)

       -p | --no-startup
              Don't call the script to bring up network on deamon start (default: off)

       -q | --no-shutdown
              Don't call the script for network shutdown on deamon quit (default: off)

       -w | --wait-on-fork
              When  daemonizing, wait until the background process finished with the initial link beat detection. When this is enabled, the parent
              process will return the link status on exit. 2 means link beat detected, 3 stands for link beat not detected, everything else is  an
              error.

       -W | --wait-on-kill
              When killing a running daemon (with -k) wait until the daemon died.

       -x | --extra-arg= ARG
              Specify an extra argument to be passed to the action script.

       -M | --monitor
              Don't  fail  when the network interface is not available, instead use NETLINK to monitor device avaibility. The is useful for PCMCIA
              devices and similar.

       -h | --help
              Show help

       -k | --kill
              Kill a running daemon (Specify -i to select the daemon instance to kill)

       -c | --check-running
              Check if a daemon is running for a given network interface. Sets the return value to 0 if a daemon is already running or to  255  if
              not.

       -v | --version
              Show version

       -S | --supend
              Suspend  a running daemon. The daemon will no longer check the link status until it is resumed (-R) again. (Specify -i to select the
              daemon instance to suspend.)

       -R | --resume
              Resume a suspended daemon. (Specify -i to select the daemon instance to resume.)

       -z | --info
              Request that a running daemon shall write its status information to syslog. (Specify -i to select the daemon instance  to  send  the
              request to.)

FILES

       /etc/default/ifplugd:  this  file  is  sourced  by  the  init script /etc/init.d/ifplugd and contains the interface to be monitored and the
       options to be used.

       /etc/ifplugd/ifplugd.action: this is the script which will be called by the daemon whenever the state of the interface  changes.  It  takes
       two areguments: the first is the interface name (eg. eth0), the second either "up" or "down".

       /var/run/ifplugd.<iface>.pid: the pid file for ifplugd.

ENVIRONMENT

       The action script will be called with two environment variables set:

       IFPLUGD_PREVIOUS  The  previous link status. Either "up", "down", "error" or "disabled". The former values should be obvious, the latter is
       set on daemon startup.

       IFPLUGD_CURRENT The current link status. See above for possible values.

SIGNALS

       SIGINT, SIGTERM ifplugd will quit, possibly running the shutdown script. This is issued by passing -k to ifplugd.

       SIGQUIT ifplugd will quit, the shutdown script is never run.

       SIGHUP ifplugd will write its status information to syslog. This is issued by -z.

       SIGUSR1 ifplugd will go to suspend mode. (-S)

       SIGUSR2 ifplugd will resume from suspend mode. (-R)

AUTHOR

       ifplugd   was   written   by   Lennart    Poettering    <mzvscyhtq    (at)    0pointer    (dot)    de>.    ifplugd    is    available    at
       http://0pointer.de/lennart/projects/ifplugd/

SEE ALSO

       ifplugd.conf(5), ifup(8), interfaces(5), ifconfig(8), ifplugstatus(8)

COMMENTS

       This man page was written using xmltoman(1) by Oliver Kurth.

Manuals                                                                User                                                             ifplugd(8)