Hi,
I assume there is a simple solution, but as usual i can't find it!
How can i add a line of text to the end of a text file on a new line?
i.e
file.txt
________________
this is my text file
________________
file.txt
________________
this is my text file
WITH A NEW LINE... (6 Replies)
Hi,
I want to add \n as a EOF at the end of file if it does't exist in a single command. How to do this?
when I use command
echo "1\n" > a.txt
and
od -c a.txt
0000000 1 \n \n
0000003
How does it differentiate \n and eof in this case?
Regards,
Venkat (1 Reply)
Hi All,
I have a file as below:
cat myfile
abcdef
NA
rwer
tyujkl
na
I wish to add the text ".txt" at the end of all lines except the lines starting with NA or na.
I know i can add text at the end of line using following command but I am not sure how to valiate the condition. (14 Replies)
(sh shell) I have a function I am using that does a date calculation so I can subtract dates.
get_JD () {
bc << MSG
scale=0
date calculation ……….......
MSG
}
Then I have this little script that runs after it.
read XXX < TESTFILE
pastdate=`get_JD $XXX`
currdate=`get_JD &YYY`... (2 Replies)
Well here goes:
I tried to write a batch file that adds a specific fixed text to each line of an already existing text file.
for the adding text infront of each line I tried this:
for /F "delims=" %%j in (list.txt) do echo.STARTTEXT\%%j >> list.txt
for adding text after each line I... (0 Replies)
I'd like to write up notes in a relatively readable format and then use a shell script to add LaTeX formatting. Specifically, I'm trying to figure out how to add the LaTeX newline character (\\) to the end of lines without \begin{} or \end{} statements
example notes file:
\begin{enumerate}
--... (2 Replies)
Dear All
I am having a text file which is having more than 200 lines.
EX:
001010122 12000 BIB 12000 11200 1200003
001010122 2000 AND 12000 11200 1200003
001010122 12000 KVB 12000 11200 1200003
In the above file i want to search for string KVB... (5 Replies)
Hello All,
this is my first post so I don't know if I am doing this right.
I would like to append entries from a series of strings (contained in a text file) consecutively at the end of specifically labeled lines in another file.
As an example:
- the file that contains the values to be... (3 Replies)
so...
Lets assume I have a text file.
The text file contains multiple "#" symbols.
I want to replace all thos "#"s with a STRING using DOS/Batch
I want to add a certain TEXT to the end of each line.
How can I do this WITHOUT aid of sed, grep or anything linux related ? (1 Reply)
Seems simple but ive been searching for a good hour of so
I have a text file and would like to add a string to the end of line 5 ( as an example)
to ake tings hard the line number we have to add the text to is stored in a variable cunningly name $Line_to_append
any ideas on how this could... (2 Replies)
Discussion started by: dunryc
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)