I have installed Win98 OS .......1st
then RH7.2
with GRUB bootloader okay
i.e in the Grub there is two choices 1-Linux
2-Dos
also I install bootloader of linux in MBR -master boot record-
when select Linux an error :
... (6 Replies)
Hey everyone,
I'm new to the forum.
I have a problem with Mandrake 8.00; i have installed it on my old PC with no problems (none mentioned) but on re-booting after the installation it just hangs after listing the devices: Hard Disk, CD-ROM & Floppy A.
I have installed it on Packard Bell with... (2 Replies)
When running top, I notice a bit more I/O wait time than usual. Is there a tool or piece of software out there that can me help evaluate the performance of these operations on my machine? Thanks! (5 Replies)
Hi ALL:
I am not able to get the response back from weblogic in the shell script.
The weblogic server in different account. I am able to login to that account and bring the server up but while doing a ping, the script is failing. While the same script is running fine if I run it on the account... (1 Reply)
count2=0
var2=NOT
if
then
echo"Loop1"
command="egrep ',$var1,"
if
then
echo "the command is OR"
command=$command"|,$var3,"
echo "$command"
elif
then
command=$command"| egrep ',$var3,"
else
... (4 Replies)
Did not use 'wait' yet.
How I understand by now the wait works only for child processes, started background.
Is there any other way to watch completion of any, not related process (at least, a process, owned by the same user?)
I need to start a background process, witch will be waiting... (2 Replies)
Hey friends, below mentioned script is giving me proper o/p which can be 1 or 2
echo select status_ac from db_acct where acct_num='$1'" | dbaccess elstest
Now I want to interpret the o/p as follows.
If o/p is 1 then YES
If o/p is 2 then No
And to do this I have modified above... (2 Replies)
Hello, I have been trying to figure out why the wait isnt waiting for the sleep process to complete till now and have found out that since sleep runs as different process and not a child process the wait isnt waiting.
script:
cat test|while read i
do
echo $i
sleep 30 &
done
wait
ps... (4 Replies)
Iam having a script which is used to load users and dumpfile in any given schema.Iam trying to autolog the script and have added two fucntion in it.
function init_stdout_redirect {
OUT_LOG=$1
OUT_PIPE=$(mktemp -u)
# Create the output pipe
mkfifo $OUT_PIPE
# Save stdout and... (15 Replies)
Hi,
I have run into a problem to which i can't seem to find any solution, posting here is my last resort.
Problem:
I am using plink to access my router and run a few configuration commands. When in enter configurations mode, instead of sending next command plink keeps on waiting for manual... (7 Replies)
Discussion started by: zaainabbas
7 Replies
LEARN ABOUT ULTRIX
load
load(8) System Manager's Manual load(8)Name
load - down-line load software to a target node
Syntax
/etc/load [ node ]
Description
The command loads software to an unattended target node. The target node is loaded by the host that executes the command.
The command requires the identification of the service circuit over which the load is performed, the Ethernet hardware address of the tar-
get node, and the service password needed to gain access to the target. This information is included in the nodes database entry for the
target node. A node entry is defined with the command. For further information, see The node is the name or address of the target node.
A node name consists of from one to six alphanumeric characters. For single networks, a node address consists of a decimal integer
(1-1023). For multiple networks, a node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
Options-p Uses the specified service and password (next arguments) in accessing the target node. You can omit a target node's service and pass-
word from the nodes database for security reasons, but you must then specify the service and password in the command line by using the
option.
Examples
# /etc/load bangor -p 130fe
This command causes node to be loaded by the ULTRIX host node executing the command. The ULTRIX host uses the load files specified in the
nodes database entry for node to perform the load.
See Alsoaddnode(8), ccr(8), getnode(8), mop_mom(8), remnode(8), trigger(8)
Guide to Local Area Transport Servers
load(8)