i'm having 2 problems.
1. the system will always look to boot from the net. i've changed the prom settings so that it boots from the disk, by entering "setenv boot-device disk0:3", but the system still seems to want to boot from the net.
2. i replaced my creator3d with an elitem6 and i did... (6 Replies)
hardware on my first FreeBSD server has crashed. i was planning on
swapping the HD into another machine, booting the generic kernel and then
custom tailoring it to the new machine specs.
however, i'm having a problem.
the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on?
{0} ok boot
/ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f
SunOS Release 5.9... (3 Replies)
Hello those more knowledgeable than I:
I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list:
-install xp, image it, move the partition to the end of drive, verify it boots, image again,
-boot off of SCO... (6 Replies)
I have a pentium IV with 512 MB ram and 80 GB HDD.
I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
I have installed WAMPSERVER 2.0 on my windows vista x64 system but still am having issues with getting the webserver to be seen outside my local network. It is working fine within my local network.
Been through several setup tutorials so far, no dice still.
For testing purposes I have... (1 Reply)
I have a Jumpstart server. It does not have Apache on there. I have not found a step by step guide on how to install a WAN boot server. I already have all my custom files from my Jumpstart Server and the flash as well. I just want to test it over the WAN and see if I can get it to work.
I... (2 Replies)
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
I am installing Red Hat Linux 6.9 as a VM in Hyper-V on an HP laptop running Windows 10. After the install completes and the VM reboots, it gives me the message, "Detected CPU Family 6 model 142; Warning: Intel CPU model - this hardware has not undergone testing by Red Hat and might not be... (1 Reply)
Discussion started by: tigers580307
1 Replies
LEARN ABOUT DEBIAN
ipsec_version
IPSEC_VERSION(5) [FIXME: manual] IPSEC_VERSION(5)NAME
ipsec_version - lists KLIPS version information
SYNOPSIS
cat /proc/net/ipsec_version
OBSOLETE
Note that ipsec_version is only supported on the classic KLIPS stack. It is not supported on any other stack.
DESCRIPTION
/proc/net/ipsec_version is a read-only file which lists the currently running KLIPS version information.
EXAMPLES
FreeS/WAN version: 1.4
shows that the currently loaded KLIPS is from FreeS/WAN 1.4.
FILES
/proc/net/ipsec_version
SEE ALSO ipsec(8), ipsec_manual(8), ipsec_eroute(5), ipsec_spi(5), ipsec_spigrp(5), ipsec_klipsdebug(5), ipsec_tncfg(8), ipsec_pf_key(5)HISTORY
Written for the Linux FreeS/WAN project <http://www.freeswan.org/> by Richard Guy Briggs.
[FIXME: source] 10/06/2010 IPSEC_VERSION(5)