I'm getting the below error while trying to create a SEA adapter in VIOS
Code:
$ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1
Some error messages may contain invalid information
for the Virtual I/O Server environment.
Method error (/usr/lib/methods/cfgsea):
0514-040 Error initializing a device into the kernel.
Command did not complete.
"Run mkdev" was last subcommand run.
$
Not sure what this means.. Can someone throw some light in this
I am trying to create a SEA on a LHEA port and it gives me error
lsdev -Cc adapter:
ent0 logical host ethernet port (l-hea)
ent1 virtual I/O ethernet adapter
mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199
method error (/usr/lib/methods/cfgsea):
Failed to configure SEA... (0 Replies)
Hi all,
I set up the following configuration on my system:
- An LPar with a virtual adapter, first one with a vlan id=703 and id port=13.
- The first adapter have to connect to a VIOS in which i configured an SEA.
So, the VA is set up on interface ent2, SEA on ent29 (by linking a... (0 Replies)
Hi experts, i got a 4-port Adapter card on VIOS and would like to configure 4SEA for 4 difference segment IP client's LPAR use, first SEA succeed to be configured on ent0 but once second SEA configured, first SEA fail to be connected. Any issues i need to be concerned in order to configure 4 SEA on... (8 Replies)
I am trying to install a VIOS pair with a load-sharing SEA adapter, following this recipe from Developerworks. Without load-sharing everything went fine and worked as expected, but somehow i am a bit lost and the first tries with "ha_mode=sharing" didn't work at all.
Here is the situation:
I... (6 Replies)
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
i want configure a SEA over my vios ,
i have a message error :
Method error (/usr/lib/methods/cfgsea):
Failed to configure SEA with return code 1 and SEA-specific error code 10:
Detailed info: Setting real adapter ent1 in promiscuous mode failed... (5 Replies)
hi guys
BTW pretty new to VIO
I inherited 2 I BM Power Server - blades PS701 - One is already configured using en8
# lsdev -Cc adapter | grep ent
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available 04-20... (8 Replies)
hello,
what will happen if i try to move sea of my 1 vio server to standby( using chdev command), when sea of other vio server is already in standby mode? (1 Reply)
Hello,
I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time.
Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
LEARN ABOUT DEBIAN
mojo::server::morbo
Mojo::Server::Morbo(3pm) User Contributed Perl Documentation Mojo::Server::Morbo(3pm)NAME
Mojo::Server::Morbo - DOOOOOOOOOOOOOOOOOOM!
SYNOPSIS
use Mojo::Server::Morbo;
my $morbo = Mojo::Server::Morbo->new;
$morbo->run('./myapp.pl');
DESCRIPTION
Mojo::Server::Morbo is a full featured self-restart capable non-blocking I/O HTTP 1.1 and WebSocket server built around the very well
tested and reliable Mojo::Server::Daemon with "IPv6", "TLS" and "libev" support.
To start applications with it you can use the morbo script.
$ morbo myapp.pl
Server available at http://127.0.0.1:3000.
Optional modules EV, IO::Socket::INET6 and IO::Socket::SSL are supported transparently and used if installed. Individual features can also
be disabled with the "MOJO_NO_IPV6" and "MOJO_NO_TLS" environment variables.
See Mojolicious::Guides::Cookbook for more.
ATTRIBUTES
Mojo::Server::Morbo implements the following attributes.
"watch"
my $watch = $morbo->watch;
$morbo = $morbo->watch(['/home/sri/myapp']);
Files and directories to watch for changes, defaults to the application script as well as the "lib" and "templates" directories in the
current working directory.
METHODS
Mojo::Server::Morbo inherits all methods from Mojo::Base and implements the following new ones.
"check_file"
my $success = $morbo->check_file('/home/sri/lib/MyApp.pm');
Check if file has been modified since last check.
"run"
$morbo->run('script/myapp');
Run server for application.
SEE ALSO
Mojolicious, Mojolicious::Guides, <http://mojolicio.us>.
perl v5.14.2 2012-09-05 Mojo::Server::Morbo(3pm)
06-24-2010
VIOS SEA Creation
