i'm having 2 problems.
1. the system will always look to boot from the net. i've changed the prom settings so that it boots from the disk, by entering "setenv boot-device disk0:3", but the system still seems to want to boot from the net.
2. i replaced my creator3d with an elitem6 and i did... (6 Replies)
hardware on my first FreeBSD server has crashed. i was planning on
swapping the HD into another machine, booting the generic kernel and then
custom tailoring it to the new machine specs.
however, i'm having a problem.
the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on?
{0} ok boot
/ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f
SunOS Release 5.9... (3 Replies)
Hello those more knowledgeable than I:
I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list:
-install xp, image it, move the partition to the end of drive, verify it boots, image again,
-boot off of SCO... (6 Replies)
I have a pentium IV with 512 MB ram and 80 GB HDD.
I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
I have installed WAMPSERVER 2.0 on my windows vista x64 system but still am having issues with getting the webserver to be seen outside my local network. It is working fine within my local network.
Been through several setup tutorials so far, no dice still.
For testing purposes I have... (1 Reply)
I have a Jumpstart server. It does not have Apache on there. I have not found a step by step guide on how to install a WAN boot server. I already have all my custom files from my Jumpstart Server and the flash as well. I just want to test it over the WAN and see if I can get it to work.
I... (2 Replies)
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
I am installing Red Hat Linux 6.9 as a VM in Hyper-V on an HP laptop running Windows 10. After the install completes and the VM reboots, it gives me the message, "Detected CPU Family 6 model 142; Warning: Intel CPU model - this hardware has not undergone testing by Red Hat and might not be... (1 Reply)
Discussion started by: tigers580307
1 Replies
LEARN ABOUT SUNOS
ickey
ickey(1M)ickey(1M)NAME
ickey - install a client key for WAN boot
SYNOPSIS
/usr/lib/inet/wanboot/ickey [-d] [-o type=3des]
/usr/lib/inet/wanboot/ickey [-d] [-o type=aes]
/usr/lib/inet/wanboot/ickey [-d] [-o type=sha1]
The ickey command is used to install WAN boot keys on a running UNIX system so that they can be used the next time the system is installed.
You can store three different types of keys: 3DES and AES for encryption and an HMAC SHA-1 key for hashed verification.
ickey reads the key from standard input using getpassphrase(3C) so that it does not appear on the command line. When installing keys on a
remote system, you must take proper precautions to ensure that any keying materials are kept confidential. At a minimum, use ssh(1) to pre-
vent interception of data in transit.
Keys are expected to be presented as strings of hexadecimal digits; they can (but need not) be preceeded by a 0x or 0X.
The ickey command has a single option, described below. An argument of the type -o type=keytype is required.
The ickey command the following option.
-d
Delete the key specified by the keytype argument.
On success, ickey exits with status 0; if a problem occurs, a diagnostic message is printed and ickey exits with non-zero status.
/dev/openprom
WAN boot key storage driver
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWwbsup |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
ssh(1), openprom(7D), attributes(5)
7 May 2003 ickey(1M)